Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Check the owner's manual and make sure that you have all of the parts. 01 Stand (MDS-4) TD-4K parts 02 03 04 05 Adjusting the tension (PDX-8) Stereo 1/4” plug Stereo Headphones 1/4” plug (mono) Amplified speakers, etc. Indicator to AC outlet AC adaptor Power cable * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Assembly procedure Connection procedure Align with indentation Tighten the bolt with a drum key. Rotation stopper (note orientation) Check the included items Setup Guide Hi-hat control pedal (FD-8) .. Kick trigger pad (KD-8) .. Cymbal pad for hi-hat (CY-5) .. Cymbal pad for crash/ride (CY-8 x 2) .. V-Pad for snare (PDX-8) .. Pad for tom (PD-8 x 3) .. Drum sound module (TD-4) .. Connection cable (special for TD-4) .. ..AC adaptor Drum key (Included in the FD-8 packing carton.) .. Assemble the stand Attach the parts Cymbal mounts Pad mounts Pad mounts If the stand wobbles, loosen this hand knob and adjust the height. Hi-hat mount As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer. 1.0 m (40”) Connect the pads to the sound module Connect the cable to the TD-4 as shown in the illustration. 1. Labels indicating the pad to be connected are attached to the cable. Make connections as shown in the illustration. 2. Connect the AC adaptor and speakers Wing nut Felt washer Attach the snare (PDX-8) and toms (PD-8) Attach the hi-hat (CY-5) Attach the crash cymbal (CY-8) and ride cymbal (CY-8) Assemble the kick (KD-8) Upper clutch Clutch felt (large) Lower clutch Clutch felt (small) While pressing Use Drum Key to tighten Attach the sound module (TD-4) Assemble the hi-hat control pedal (FD-8) Anchor bolt Shallower Deeper Slide the arm Attach the anchor bolt Adjusting the pedal depth (if installing on a drum mat) Anchor bolt Spring for the anchor bolt Loosen with the drum key, and tighten after adjusting 1 4 3 2 5 6 Use cable ties to fasten the cables at the circled locations “ ” so that they do not interfere with your performance. Make sure to wrap the cable ties around the pipes. * Assemble the stand using the procedure described in the MDS-4 Owner’s Manual. * Do not spread the stand wider than 1.0 meters (40 inches). Attach the bolt so that it is at the right when seen by the performer. Tighten the wing nut to obtain an appropriate amount of sway. Finger-tighten all six of the tuning bolts in the sequence shown in the illustration. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. Use the drum key to adjust the tension as needed. 1. 2. 3. Remove the screws Pull out the stand in the direction of the arrow, and use the screws you removed earlier to fasten the stand. KD-8 (Kick) 03 05 When using on the drum mat When using on hard-surfaced flooring Adjusting the anchor bolts When using the kick pedal on a drum mat or similar surface, adjust the anchor bolts so their tips protrude from the plate. Then, secure the pedal in place; this will make it easier to use the kick pedal. However, when used on hard-surfaced fl ooring, the anchor bolts may damage the fl oor. Adjust the anchor bolts correctly. When using a twin pedal Position the two beaters equally apart from the center of the pad as shown in the fi gure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired. Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the sensitivity on the sound module. NOTE The tips of the anchor bolts are sharp. Handle with care. * Head Anchor bolt Stand Output jack Foot plate Detailed explanation of each part KD-8 component * Use a commercially available kick pedal. Other side This completes assembly and connections. Rod Tighten Loosen Rod Tighten Loosen To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, use cable ties to fasten the cord from the AC adaptor to the stand. * Setup Guide (this document) Owner’s Manual .... Manual set Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. 01 02 03 Beater Install the kick pedal securely. Commercially available kick pedal Beater * Adjust the height so that the entire pedal comes into contact with the floor. This hight will vary depending Position the beater so that it on your kick pedal. ...