Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Higher settings will increase the level of the signal that is sent to the effect unit, causing the effect sound that is produced to be louder. The result is that the effect becomes deeper. For the equalizer of System effects, on the other hand, you can select whether the sound of the Part will pass through the equalizer or not; i.e., make an on/off setting to modify the sound. Insertion Effects Insertion effects are effects that modify the sound itself, and are able to give it a completely different character. SK-88Pro provides 64 types of effects. As shown in the diagram at right, you can select one Insertion effect, and specify for each Part whether or not the sound will be routed through the effect (on/off). Since only one type of Insertion effect can be applied at a time, turning it on for two or more Parts will cause the sound of these Parts to be mixed. If a System effect is applied to a Part for which the Insertion effect is turned on, the Insertion effect Send Level will be used instead of the Send Level of the Part itself, (p.63) System Mode Setting The type of effects that are available here will depend on the System mode setting (p. 138). In Single Module mode (mode 1), each will have one set of effects. In Double Module mode (mode 2), equalizer and delay are unavailable, but there are two sets each for Reverb and Chorus settings, and these can be used simultaneously. This is especially valuable when you wish to have different effect types or settings for each Part. Also, the Insertion effect can be used only for the Part group A. This is every effective when you wish to apply a special effect to the solo part that you play. 54 5. SYSTEM EFFECTS Single Module mode is the Normal mode in which you can use 32 Parts, and Double Module mode is the mode in which you can use the SK-88Pro as two sound modules (Part Groups A and B). For details refer to p. 138. 55 5. SYSTEM EFFECTS Reverb/Chorus/Delay The System effects of the SK-88Pro include 8 types of reverb and chorus, and 10 types of delay. In addition, for each of these effects you can specify parameter values such as character, depth, rate and time. For these effects, you can set the overall level for all Parts and also individual levels for each Part. * For settings for each Part, this will be the Send Level Reverb Reverb is an effect that adds reverberation to a sound, as you would hear in a concert hall. Chorus Chorus broadens the spatial image of the sound, adding depth and richness. Delay Delay creates echoes. It is also possible to give depth and width to a sound by adding a short delay to the original sound. Adjusting the Level of Reverb/Chorus/Delay When you want to adjust the level for all Parts, press the [ALL] button to make the button indicator light. When you want to adjust the level for each Part, make sure that the [ALL] button is dark, and use the PART [-^] [►] buttons to select the Part you wish to modify. 2 Press the button of the effect you wish to adjust. REVERB [*«] [►]: Reverb level (for all Parts) Reverb Send Level (for each Part) CHORUS [-4] [►]: Chorus level (for all Parts) Chorus Send Level (for each Part) DELAY [<] [►]: Delay level (for all Parts) Delay Send Level (for each Part) (while holding down the [88 MAP] button, press the DELAY [<] [►] buttons) You can not select the System effect parameters individually for the Part with Insertion effect "on." If a System effect is applied to a Part for which the Insertion effect is turned on, the Insertion effect Send Level will be used instead of the Send Level of the Part itself. The area of the display where the Delay setting is displayed is shared with the KEY SHIFT display. When while holding down the [88 MAP] button, press the DELAY M [►] buttons, the delay setting will be displayed. And when while not holding down the [88 MAP] button, the KEY SHIFT [►] buttons are pressed, the Key Shift setting will be displayed. If the display indicates a +/- (plus or minus) value, the Key Shift setting is being displayed, (p. 100) Showing the Settings Graphically When you perform the following operation, the current parameter value of Reverb or Chorus will be displayed graphically. 1. Simultaneously press both the [<] [►] buttons of REVERB or CHORUS. The current parameter value of Reverb or Chorus will be displayed. 2. Simultaneously press both buttons once again and the previous display will reappear. 56 5. SYSTEM EFFECTS Setting Reverb/Chorus/Delay Parameters O O C 0 © UTIL MUTE _LEVEL _ o o c El_SLssO B- ■O’ c 1 Press the [ALL] button to make the button indicator light. Press the [EDIT] button. Use the [A] [T] buttons to select the parameter you wish to modify. While holding the [SHIFT] button, press the [A] [▼] button to skip parameters. PART INSTRUMENT ALL i-Reuerbï Hal 12 LEVEL PAN 127 0 ' Use the INSTRUMENT [-4] [►] buttons to set the value. PART INSTRUMENT HLL >R00rb: P1 at-e LEVEL PAN 127 0' When you finish making set...