Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
When signals reach the clipping level (~6dB), the indicator lights in red. 0 Sens Knob This knob adjust the sensitivity of the input signal. Set this so that the Peak/Signal Indicator will light green and occasionally red. If the Peak/Signal Indicator does not light up at all, rotate the Sens Knob clockwise or increase the level of the input signal. * Channels 1 and 2 have rated inputs of -50 to -10dBm which are appropriate input sensitivities for microphone level, while Channels 3 to 16 have -20dBm to +4dBm rated input appropriate for line level. 0.0 and @ Effect Volume Knobs These adjust the level of the signals to be sent to Effect Sends. * The position where the signals are sent to the Effect Send is Post Fader (after passing the Channel Fader). 0 AUX Volume Knob This adjusts the level of the signal to be sent to the AUX Send. This, therefore, can be used for monitor sending, recording output or effect sending. " The position where the signals are sent to the AUX Send can be selected at the Master Section; Pre or Post. Q Panpot This sets the placing of the sound imaging in stereo sound field. At the center position, the volumes of L and R are equal. Q Channel Fader This sets the level of the signal to be sent out from a Channel. * Before switching on or off the mixer, be sure to set the Master Fader to zero. * For about 3 seconds, muting circuits work, therefore, no sound is output. 6 2. Master Section MASTER O Peak Meters Use these peak-indicating level meters to observe the ouptut levels from the Master Out's. When "OdB" lights up, the level Irom the Master Out is +4dBm. 0 Pre-fader Signal Indicators These can be used to observe the output levels of the amplifiers where signals from Channels are mixed. The position where the signals are read is Pre Master Fader (before the Master Fader). When it is equal to the rated level -20dB, the indicator lights in green, and when it is clipping level -6dB, it lights in red. © Master Faders These adjust the final sending levels of the mixed signals. 00-0 and 0 Return Volume Knobs These adjust the levels of the signals sent to the Return Jacks. 0 Panpot This sets the sound imaging of the Return 4. At the center position, the volumes of L and R are the same. 0, © and 0 Effect Send Volume Knobs These adjust the levels of the signals to be sent to the effect units. © AUX Send Volume Knob This adjusts the final sending level of the signal mixed at the AUX Volume of each Channel. © AUX Selector Switch This selects the position where the signals are sent to the AUX Send. When PRE is selocted, the signals are taken before the Channel Fader, therefore, the mixer can be used as a monitor. When POST is selected, the signals are taken after the Channel Fader, therefore the mixer can be used as an effect send. © Headphone Volume Knob This adjusts the volume of the headphone signals which are the mixture of the signals from each Channel Fader and the Phones Mix In. ' I he signals are sent out before going to the Master Fadei, therefore the headphones can be used for monitoring © Headphone Jack Connect stereo headphones to this jack. © Power Indicator This lights up when the mixer is switched on 0 Power Switch Pushing this switch turns the mixer on, and pushing it again turns off. * Before turning on or off the mixer, be sure to set the Master Faders to zero. * For about 3 seconds after the mixer is turned on, muting circuits work, therefore no sound is output. 7 3. Rear Panel O Input Jacks Channels 1 and 2 are for connecting microphones, musical instruments, etc. Channels 3 to 16 are for devices with line level and musical instruments. 0 Level Switch This selects the input level for the Returns 1 and 2 depending on the connected unit. 0 Return Jacks These are to feed the signals returned from the effect units. These can also be used as AUX input jacks. Returns 1 to 3 are for stereo input, and Return 4 is for monaural only. Returns 1 to 3 can also be used as monaural inputs if L sides are connected. 0 Phones Mix In Jack This is to feed the Monitor Mix signal, sequencer click sound, etc. The input signals are sent to the Headphone Jack only. * The signals fed through this jack are not sent to the Master Out 0 Master Out Jacks These are to connect to a power amplifier, etc. O Master Out Connectors These are XLR (balanced) type connectors for connecting a power amplifier, etc. The standard jacks 0 and the XLR connectors 0 can be used simultaneously. * The XLR Connectors of this unit are standardized to 1st pm-Ground, 2nd pin-Cold and 3rd-Hot. When connecting to the other unit, check the type of the connectors. 0 Effect Send Jacks These are to send the signals to the effect units 0 AUX Send Jack This sends out the signals to a monitor or effect unit. o Bus In Jacks Signals fed through these jacks can be directly mixed with the Effect Send and AUX Send Busses. When two mixers are stacked, connect the Effect Send of one...