Votes - 2, Average rating: 5
(
)
)
|
Photos and specs Roland LX-10 |
manual abstract
The customer should not attempt to assemble the instrument. • Make sure that another person is on hand to help with the assembly and setup. • Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws. • Since this product is very heavy, you must make sure that a sufficient number of people are on hand to help, so you can lift and move it safely, without causing strain. • Should you remove the screws, and cord clamps, keep them in a safe place out of children’s reach, so there is no chance of them being swallowed accidentally. • Please consult your Roland dealer to assemble the piano. Roland cannot warrant the safety of the assemble operation, if this operation is carried out by the customer. Checking the Included Items Before you begin assembling the stand, check that all the parts were supplied. (A) (A) (B) (C) (D) (E) (e) (a) (c) Left Right (b) (d) (f) (F) (G) Attach these to the stand in step 6 of “Assembling the stand.” These parts are attached from the rear side. (H) (I) . Phillips screwdriver . Thick blanket This is used to protect the piano, and to avoid scratching the walls or floor of the location where the assembly is performed. Be sure to use a blanket of sufficient size. A Side board L 1 R 1 B Pedal board 1 C Front board (with speaker box) 1 D Rear board 1 E Rear board Upper 1 F Cord clamps 3 G Stabilizer L 1 R 1 H Screwdriver 1 I Felt 2 a Screws (M6 x 20 mm) 4 b Screw (M5 x 20 mm) 10 c Screws (M4 x 16 mm) 5 d Screws (M5 x 40 mm) 4 e Thumbscrew 3 f Screws (4 x 16 mm) 6 Assembly Procedure The packing sheets that protect the side boards should not be removed until you have finished the step “2. Assembling the stand.” This will prevent the side boards from being scratched during assembly. * Packing sheets * First, assemble the unit provisionally, using your fingers to lightly tighten the screws. Next, use a screwdriver to securely tighten the screws, then place the unit on a flat and stable surface. * Do not allow the pedal cord or power cord to get twisted or pinched while assembling the unit. • The surfaces of the piano unit and of the stand are easily scratched; handle with care to avoid scratching them. • Do not place the main piano unit directly on the floor. Doing so will damage the External memory holder located on the bottom panel, or the Bottom Panel case. * Lay down a thick blanket on your work surface to prevent the stand or the floor from being scratched. 1. Fasten the side boards L/R (A) to the pedalboard (B) as shown in the illustration, using two screws (d) each at the left and right sides. 2. Taking care that the pedalboard (B) is not twisted, raise the assembly upright. 3. From above, pass the front board (C) through the gap in the side panel hardware, and insert it so that it is in complete contact with the holder on the rear side. * This step must be carried out by at least two people. * Be careful not to scratch the front boards. * Do not grasp the mirror surface of the front board. Doing so may scratch the mirror surface. 4. Fasten the top part of the front board (C) to the left and right side boards (A) using one screw (a) each at the left and right sides. Next, fasten the rear and bottom of the speaker box to the side panel using two screws (b) each at the left and right sides. Finally, fasten the bottom of the front board (C) to the pedalboard (B) using screws (b) at four locations. * Tighten the screws in the order shown above. Distortion may occur if you fail to observe the correct order. * If your screwdriver will not go in when tightening the screws of the pedalboard, use the included screwdriver (H). 5. Fasten the rear board (D) using screws (c) at five locations. 6. Attach the stabilizers. Stabilizer hardware to prevent tipping is included with the LX-10. There is no danger of tipping with normal use. However, if you will not be placing the piano against a wall, you should attach the stabilizers for maximum safety. Please be aware that even if the stabilizers are attached, tipping may still be possible under certain circumstances of handling. Please use caution. Lay the stand forward as shown in the illustration, and attach the stabilizers (G) to the bottom of the stand using screws (f) at three locations each for the left and right sides. * Take care not to attach the left and right stabilizer to the wrong sides. 7. Remove the packing sheet from the left and right side boards. Assembly Procedure 1 Check Before Assembling 2 Assembling the Stand (A) (B) (A) (d) (d) (d) M5 x 40 mm Route the pedal cord outside. (C) The speaker box is attached to the rear. Mirror surface Gap (C) (a) (a) (b) (b) (b) (bb) (b)b b (b) (b) (b) (a) M6 x 20 mm (b) M5 x 20 mm (c) (c) (c) (c) (D) (c) (c) M4 x 16 mm (G) Left Right (f) (f) (G) 4 x 16 mm * This step must be carried out by at least two people. 1. With another person helping you, lift the instrument at its left and right ends and place it on the holder hardware at the top of...