Votes - 4, Average rating: 4.3 ( )

Manafacture: Roland File size: 4.62 mb File name: Language of manual:

Other manuals for this model:

Musical Instruments - JD-800 (20.45 mb)

The blinking “ ” mark indicates the position at which an effect will be inserted. F' H T U H E F F b 0 '-1 u 0 n c ■=• H *—DS---PH---SP---EN- © Use CURSORp<~| to move the “ ” mark to the location you want to change. PhTuH EFF Sequence fl -DS---PH-f-SP---EN~ I- 18 1. PATCH EDITING Make effect settings (Single mode) Use KSaQsElor the I INC/YES I and | DEC/NO | keys to select an effect to occupy that location in the chain of effects. The selected effect will blink. ' H T U H E F F bf •"■I U ■=■ n <_• S' A -DS---PH-DS-SP---EN- Blinking After specifying the effect to occupy that location, press CURSORjjjTJfF]. The effect will be inserted at that position, and the order will change. The “ + ” mark will reappear, and you can repeat steps (2) and (3) to arrange the effects in the desired order. PATCH EFF Sequence 0 -C H---[ 3—►-SP---EN~ (§) Next, press PAGEfAl. In this page you can turn each effect on/off. A display of “ £ ] ” indicates that the effect assigned to that location has been turned off. Effects that are turned on are indicated by their abbreviation. PATCH EFF Switch A K 3---C ]---SP----EN- © Use CURSORHH10 move the “ ► ” mark to the effect you wish to turn on/off. PATCH EFF Switch A -[ 3---E ]— ►SP----EN- Use VALUE or the INC/YES] and | DEC/NO] keys to turn the selected effect on/off. PATCH EFF Switch A -C 3---11— ► [ 3---EN- Repeat steps © and (?) as necessary. n- 19 1. PATCH EDITING Make effect settings (Single mode) Press PAGE[Hn. and you can specify the effect order for group B. Use steps © to to specify the order in which these effects will be linked. F1 fi T U H E F F b i? -‘I u © n f b + -CH---DL---RU-- Press] EXIT |to return to the previous play mode. The following effects can be selected in each effect group. Effect group A: distortion (DS), phaser (PH), spectrum (SP), enhancer (EN) Effect group B: chorus (CH), delay (DL), reverb (RV) * It is not possible to reverse the order of groups A and B. ♦ When the Effect Master Switch (<=»■ II P. IH - 9) in Tune/Function is turned OFF, Chorus/Delay/Reverb of Group B do not function. 1-20 1. PATCH EDITING Make effect settings (Multi mode) O Effects in Multi mode (Output Assign/Effect Mode/Effect Level) In Multi mode, you can specify the effect assignment independently for each Part (and independently for each key of the Special Part). The diagram below shows how you can set Output Assign to “MIX”, and then select one of three Effect Modes; reverb, chorus+reverb, or delay+reverb. If Output Assign is set to “direct”, you can set the effect send level for each effect to 0, and thus indirectly turn effects on/off. To make either setting, press PART EDIT , and modify the value in Part Edit (Special Setup Edit in the case of a Special Part). For details of the various effect parameters, see the Reference Manual. Patch Tnne П Tone C Tone В Tone A ——> Patch level Part volume (MIDI volume) DIRECT OUT Press I MULTI I, and then select the same Patch as you did in Single mode. Press | PART EDIT |. Then press PAGE| A |[~T~j until the following page appears. PART EDIT Parti 0 u t F- u t A s s i 9 n И I X Blinking Use VALUE or INC/YES and DEC/NO to select “MIX”. Ш- 21 1. PATCH EDITING Make effect settings (Multi mode) © Press PAGE|~À~l. PART EDIT Parti Effect node DLV+REU Blinking Use VALUE or INC/YES and DEC/NO to select the effect. Press PAGE® to select the following page, and use VALUE or INC/YES and DEC/NO to set the level of the sound which will be sent to the effect unit. At a value of 0 there will be no effect. A value of 100 will result in the maximum effect. PART EDIT Parti E f f e c t 1 e u e I 1 U y Blinking Press EXIT to return to the previous play mode. In step (D, the following selections are available. DRY : Effects will not be applied, and only the original sound will be output. REV : the sound with reverb will be sent from the MIX OUT jacks CHO+REV : the sound with chorus and reverb will be sent from the MIX OUT jacks DLY+REV : the sound with delay and reverb will be sent from the MIX OUT jacks * When the Effect Master Switch ( er II P. Ill — 9) in Tune/Function is turned OFF, Chorus/Delay/Reverb of Group B do not function. 1-22 1. PATCH EDITING To recover the original sound d. When you finish editing Now you know how to edit Tones and Patches, but there are several points you should remember when you finish editing. To recover the original sound If you decide that you don’t like the results of your editing, here’s how to recover the original data of the Patch (the un-edited data). © While editing a Tone, press | EXIT | to return to play mode, and re-select the Patch to recover the original settings. same 1-23 1. PATCH EDITING Patch Write To store your edited sound If you decide to keep your edited sound, you must use the Write operation. Changes you make affect only the “temporary” area. If you select another Patch, the settings of the temporary are...

Download now

Please, enter two numbers from picture: