Votes - 5, Average rating: 4.8
(
)
)
|
Other manuals for this model:
manual abstract
Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet. Should you remove screws, cord clamps, or stabilizer, make sure to put them in a safe place out of children’s reach, so there is no chance of them being swallowed accidentally. ■ Check the Parts Before you begin assembling the DP-970, check that all the parts were supplied. You will also need to have a Phillips screwdriver. 1: Attachment screw (M6 x 20 mm) x 8 2: Stabilizer screw (M4 x 16 mm) x 6 3: Cord clamp x 4 MEMO The speaker box can also be installed so that it faces toward the rear instead of toward the front. Having the speaker box face out the rear of the instrument allows the speakers to be directed toward listeners when the back of the instrument faces the audience. Normal direction Front When facing to the rear Rear «— Rear Front —► ih | rij Speaker Speaker box box ■ Assembly Procedure At first, assemble the entire unit in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws. Be careful when assembling the DP-970, so as to avoid scratching the side boards. When securing the screws, lay the entire unit sideways with the rear side of the DP-970 at the bottom. 1. Secure the left side board to the speaker box with the attachment screws (in two places). Attach so that the speaker cable at the rear of the speaker box is directed to the right. 2. Secure the right side board to the speaker box with the attachment screws (in two places). 1 Attachment screw ;-1-- Speaker box Side board right Side board left 3. Set the stabilizer in the holes in the side boards (in six places). Take care not to attach the left and right stabilizer to the wrong sides. 4. Raise the entire assembly. When standing the assembled unit up, grasp near the speaker box, and gently raise the assembly. r rail La 5. Put the Pedal Board on the stabilizer. When putting the Pedal Board on the stabilizer, first loosen the attachment screws securing the speaker box to the side boards. 6. Secure the Pedal Board to the side boards with the attachment screws (in two places). Retighten the screws loosened in Step 5. Attachment screws To stabilize the pedals Temporarily loosen the screws that fasten the pedal board. Step on the pedal, and after verifying that the pedal is in firm contact with the floor, re-tighten the attachment screws firmly. 7. Align the protruding screws (one each at right and left) on the bottom of the piano with the openings in the metal fittings on the side board, then slide the piano forward until the screws are held in place. * When handling the piano, firmly grasp it at the front and back. Be careful, so you do not get your fingers pinched. Place the keyboard so that it is centered, both front to back and left to right. 8. Fasten the piano to the stand with the attachment screw (M6 x 20 mm) (one each for the right and left). 9. Connect the speaker cable extending from the rear of the speaker box to the DP-970’s speaker connector. Press the speaker cable completely into the connector so that it is securely fastened. DP-970 Rear Hold and insert the cable so that the clip portion extends into the stand and is securely connected. * Use the speaker cable with the ferrite core left attached to the cable. The DP-970 cannot be used with the ferrite core removed. 10. Connect the pedal cables to the Pedal jack. 11. As necessary, affix cord clamps as shown in the diagram to fasten the pedal cable. When Moving the Instrument Disconnect the power cord and cables from the DP-970. Then lift the piano while keeping it level, and move it with care, so that you do not drop it on your feet, or get your hands caught. Check the stability of the pedal, and make adjustments as necessary. When Disassembling Disassemble the unit by carrying out assembly Steps 111 in reverse order. When Changing the Orientation of the Speaker Box Be sure to completely disassemble the unit, change the speaker box orientation, then reassemble it. 0 2 DP-970 Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 40671590 2PD 40671590-02 DP-970 ©2005 **(0-ge, * Ь < ■««r-â^tS-MUSTo 40671590 2PD • • я §D Ч-. r\C я® vC eX Г Й » tí Г1 d Ç4- d (V - n ¿N ö; ч, Г1 (V d pjt- i+k m é ^ « m ' 9)f ¿N A •4 4 ist & ft A 0 Irl Г 1 OV T. Г Kt 9у & 0 èt Ч: d 1 О' M> T. Ä r 1 & pît- it ¿C m 4- 0 ЙМ 9+f O; (V 4 O' 0 9)f 9t A O' äo ' et hr 73& t™ * M- î Ш M %. гг. , Vi 1 \ ! / v> a-1 M 1 ¡ Jî iS 0 1 >4 %. rr. vi 1 v> a- : >4 1 ,¡ !Í ó ift H ГI ' 4 r i 54- £ft ' fi >J С IT, H I A a- r OV I èt < V> Э -в- >fr / k\ m э № 1S r I ïç fí- ...