Votes - 2, Average rating: 5
(
)
)
|
manual abstract
A wide range of rhythm variations can be produced by combining these rhythm patterns. ©Crash and Shuffle functions Equipped with Shuffle and Crash switch on the front panel. Shuffle function shuffles entire rhythms, while the Crash function can be used to insert the crash sound of Cymbal when the rhythm is changed from Intro/Fill-ln to Basic. ©Level Control for both channels All sound sources can be controlled by the Level Controls, so you can set the balance as desired. ©External In/Out Jack The CR-8000 has Trigger Out to control external sequencer or synthesizer. In addition, The Sync. In/Out section of CR-8000 allows it to be synchronized perfectly with units such as the Roland CSQ-600 Digital Sequencer or MC-4 Micro Composer. ©Precise Tempo Display The CR-8000, equipped with Digital LED Display of Tempo, can set the Tempo at any desired position with quick operation. • Slanted control panel assures easy operation. • The Accent can give emphasis to any other voices programmed on the same step. The Level control adjusts the amount of emphasis. • Do not open this unit. • Unplug this unit when it is not to be used for long periods of time. Unplug by grasping the plug rather than pulling on the cord. • Be careful not to place heavy objects on the power cord. • Avoid using this unit in very high or low temperature locations. Also keep away from heaters and air-conditioners since this type of equipment will affect circuit and pitch stability. • Avoid using this unit in very dusty or humid places. • If it is necessary to use this unit in an area with neon or fluorescent lights, keep it as far away from these lights as possible since they will induce high levels of noise. Sometimes changing the angle of this unit in relation to the lights will help reduce noise. Before Using CR-8000 Table of Contents • For the ultimate protection to the digital circuitry of your CR-8000 make ail connections to other equipment with both units power switched "OFF”. Once all connections are made, switch “ON" the power of the other unit first, the CR-8000 last, if error occurs, once switch "OFF” the power, then switch "ON” the power after about 5 seconds. • It is to be desired that Program Mode Switch is set to Play mode unless "writing" is required. This protection must be taken to make sure that the rhythms memorized into the CR-8000 are not erased or distorted. • Remember that the SYNC. In/Out Select switch must be in the OUTPUT position for the CR-8000 to operate by itself. Features ....................................1 Basic Connection ........................3 Front Panel.................... 4 OPERATION ..............................5 1. Preset Rhythm Operation ............5 2. Intro/Fill In Operation ..................6 ■To start from Intro rhythm pattern •Auto Fill In •Manual Fill In 3. How to use the Arranger...............7 ■Cymbal and Hi-Hat arrangement ■Conga and Hand Clap arrangement ■Shuffle arrangement 4. How to use the Crash Button .........7 5. How to use the Register ...............8 ■ How to set ■ How to play 6. How to write the rhythm pattern ......8 6-1 How 1o write Basic rhythm pattern ► How to erase the programmed rhythm pattern 6-2 How to write Intro/Fill In rhythm pattern .................................9 Applications 10 1. Substitute for a Metronome 2- Odd Rhythm 3. Delicate difference of rhythm variation by Register 4. Register’s special effect 5. To use the Crash sound at the ending 6. The rhythm with 32 or 24 steps Others .................................... 10 ■About Tempo Display ■ Memory Back-up ■To replace the three 1.5-Volt dry cell batteries ■ SYNC. IN/OUT.................. 11 1. Operating CR-8000 by itself 2. CR-8000+ CSQ-600 3. CR-8000+ MC-4 •Controlling CR-8000 by MC-4 •Controlling MC-4 by CR-8000 CR-8000 PRE-SET RHYTHM............12 SAMPLE RHYTHM .....................17 SPECIFICATIONS........................19 2 Basic Connection SY IN SICHRO-INPUT, OUT (See P. 11) DIGITAL SEQUENCER MC-4 CSQ-600 eic. /OUTPUT П SYNTHESIZER ANALOG SEQUENCER or DIGITAL [sequencer © r TRIGGER-OUTPUT REG 8"16"ACC REMOTE CONTROL (TYPE DP-2) INTRO STER /FILL IT START RESTART /STOP PEDAL SWITCH DP-2 ©OUTPUT ©START/STOP O RE-START Connect a Pedal Switch such as Roland DP-2 to this jack. By depressing the pedal switch, the rhythm being played can be immediately returned to the beginning of the bar, which is available for adjustment of a beat that gets out of tempo during a performance, or to create an odd rhythm. ©INTRO/FILL-IN This jack is used for remote control options for the Intro or Fill-in function (without defeating those functions at the front panel Manual button). ©REGISTER This jack provides remote control options for performing alternately two rhythm patterns without defeating this function at the front panel Register button. ©TRIGGER OUTPUT CR-8000 has Trigger Out for Control other Sequencer or Synthesizer. ©TRIGG...