Votes - , Average rating:
(
)
)
Manafacture: Roland
File size: 24.39 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after turning on is required before the unit will operate normally. * Before turning on/off the unit, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when turning on/off the unit. However, this is normal and does not indicate a malfunction. * If you need to turn off the power completely, unplug the power cord from the power outlet. Refer to “Power Supply” (p. 3). s Sound from all connected equipment can be played simultaneously. Playing a Synthesizer or V-Drums Set You can connect an audio player or other source, and play it back simultaneously. Percussion Audio Player, etc. Synthesizer V-Drums or * Use an adapter cable (such as an RCA phono to 1/4” phone adapter) as appropriate for the device you’re connecting. Playing Music from a DVD Player or Audio Player or or Do not input anything other than a stereo digital signal to the CH 3 jack. Inputting a digital signal such as 5.1 channel audio will produce noise. Set the connected device to its “stereo” or “PCM” setting. If your DVD player has a digital output jack, connect it to the CH 3 jack for the best-quality playback. DVD player Audio player Playing Music from a Mixer Connect your mixer to the BALANCED INPUT jacks. This allows you to use the system as a set of high-quality monitors. Synthesizer Mixer * Do not connect a guitar, bass, or microphone directly to the CM-110 or CM-220. Connection Examples Playing Music from a Computer If you’re connecting a computer, the following types of connections are possible. Connecting a computer via an analog connection This is the simplest type of connection. Connect your computer’s headphone jack or line output to the LINE input. Computer or Connecting a computer via a USB audio interface You can play back sound from your computer via a USB audio interface. To the coaxial output jack You can connect and play a synthesizer at the same time. Computer USB audio interface Coaxial cable * Do not input anything other than a stereo digital signal. Inputting a digital signal such as 5.1 channel audio will produce noise. * If your audio interface does not have a coaxial output jack, use the analog connection. To the analog output jacks or * Do not connect a guitar, bass, or microphone directly to the CM-110 or CM-220. NORINVINPUTINPUT NORINVINPUTINPUTm LR CH1 INSTRUMENT L/MONO LOW HIGH SPEAKER SATELLITE SPEAKER POWER OUT MASTER HPF AMP L R CH2 LINE EQUALIZER L R R STEREO CH3 DIGITAL DIGITAL RECEIVER WOOFER LPF PHASE POWER DAC AMP BALANCED INPUT L PHONES R Troubleshooting Problem Cause Action Page System won’t turn on Is the Power cord correctly connected to an electrical outlet? Make sure that the Power cord is correctly connected to an electrical outlet. p. 5 No sound Is the external equipment connected correctly? Check the type of jack and plug, and make the correct connections. — Are each of the knobs adjusted correctly? Turn the knobs toward the right to raise the volume. p. 6 Could the Auto Off function have operated? Turn the system off, then on again; or turn off the [AUTO OFF] switch. p. 6 Could you be inputting an analog signal to the CH 3 jack? Connect a coaxial cable to the CH 3 jack, and connect the other end to the digital output jack of your equipment. p. 5 Could you be inputting a digital signal such as 5.1 channel audio to the CH 3 jack? Input a stereo digital signal. p. 7 Could you have connected speakers other than the included satellite speakers? Use the included satellite speakers. p. 4 Could you be using cables other than the included speaker cables? Use the included speaker cables. p. 4 Sound is distorted or noisy Could the respective knob be raised excessively? Turn the respective knob toward the left to adjust the volume appropriately. p. 6 Is the input level from the connected device appropriate? Lower the volume of the connected device. — Could you be inputting a digital signal such as 5.1 channel audio to the CH 3 jack? Input a stereo digital signal. p. 7 Insufficient volume Is each knob adjusted correctly? Turn the knobs toward the right to raise the volume. p. 6 Is the input level from the connected device appropriate? Raise the volume of the connected device. — Could you have connected speakers other than the included satellite speakers? Use the included satellite speakers. p. 4 Could you be using cables other than the included speaker cables? Use the included speaker cables. p. 4 Could you be using a connection cable that contain a built-in resistor? When making connections to the INPUT jacks, use connection cables that do not contain built-in resistors. — Main Specifications Roland CM-110, CM-220: CUBE MONITOR CM-110 CM-220 Rated Power Output 100 W (Main Unit 50 W + Satellite Speaker 25 W x 2) 200 W (Main Unit 100 W + Satellite Speaker 50 W x 2) Nominal Input Level (1 kHz) CH 1 (INSTRUMENT): -20 dBu CH 2 (LINE): -10 dBu BALANCED INPUT: +4 dBu Input Impedance CH...