Votes - 2, Average rating: 3
(
)
)
|
manual abstract
It is transmitted via the MIDI Channel set to the Basic Channel. These are transmitted via the MIDI Channel that is set to each Pad’s Transmit Channel. However, if the Transmit Channel is set to P1–P16, S-S, C-S, or toP, the settings are not transmitted. When the Pad is struck, the Panpot value corresponding to the MIDI PAN set to the Pad is transmitted. The Panpot value MIDI PAN vv L7 0 L6 9 L5 18 L4 27 L3 36 L2 45 L1 54 Ctr 64 R1 73 R2 82 R3 91 R4 100 R5 109 R6 118 R7 127 rnd one of upper value (5) Program Change Status Second CnH ppH n = MIDI channel: 0H–FH (ch.1–ch.16) pp = Program number: 00H–7FH (prog.1–prog.128) With the Transmit Channel set to 1–16, when you switch Patches, the Transmit Channel and Program Changes set to each of the Pads in Banks A and B are transmitted. With the Transmit Channel set to P1–P16, when you strike Pads, the Transmit Channel and Program Changes set to each of the Pads in Banks A and B are transmitted. [System Exclusive Message] Status F0H: System Exclusive F7H: EOX (End Of Exclusive) With the SPD-20, the System Exclusive Message can be used to transmit Bulk Dump of patch data, instrument data, system data, chain data and sequence data. For details refer to “3. Exclusive Communications” and “Roland Exclusive Message.” [System Common Message] (1) Song Position Pointer Status Second Third F2H 00H 00H When “toP” is selected as the Transmit Channel, messages are transmitted when the Pad is struck. [System Realtime Message] (1) Start Status FAH When “S-S” is selected as the Transmit Channel, messages are transmitted when the Pad is struck. Afterwards, striking the Pad alternately transmits Stop and Start messages. (2) Continue Status FBH When “C-S” is selected as the Transmit Channel, messages are transmitted when the Pad is struck. Afterwards, striking the Pad alternately transmits Stop and Continue messages. (3) Stop Status FCH When “S-S” or “C-S” is selected as the Transmit Channel, striking the Pad after transmitting Start or Continue messages transmits. (4) Active Sensing Status FEH Normal transmission takes approximately 240 ms. 2.RECEIVED DATA [Channel Voice Message] (1) Note On Status Second Third 9nH kkH vvH n = MIDI channel: 0H–0FH (ch.1–ch.16) kk = Note number: 00H–7FH (0–127) vv = Velocity: 01H–7FH (1–127) The SPD-20 receives Note on messages on the basic channel. If the received Note number is assigned to any pad, the instrument which is assigned to that pad will sound. If there are two (or more) pads which are assigned the same Note number, the instrument priority is given to the lower (lowest) pad number. When the Layer is set at “ON”, the note number of “BANK B” is ignored. (2) Polyphonic Key Pressure Status Second Third AnH kkH vvH n = MIDI channel: 0H–FH (ch.1–ch.16) kk = Note number: 00H–7FH (0–127) vv = Value: 00H–7FH (0–127) The SPD-20 receives the message on the basic channel. If the value is greater than or equal to 40H(64), the decay of the instrument whitch corresponds to the Note number is made shorter. (3) Control Change Modulation Depth (Controller number 1) Status Second Third BnH 01H vvH Foot Control (Controller number 4) Status Second Third BnH 04H vvH Panpot (Controller number 10) Status Second Third BnH 0AH vvH Expression (Controller number 11) Status Second Third BnH 0BH vvH General purpose controller 1 (Controller number 16) Status Second Third BnH 10H vvH General purpose controller 2 (Controller number 17) Status Second Third BnH 11H vvH n = MIDI channel: 0H–0FH (ch.1–ch.16) vv = Parameter Value: 00H–7FH (0–127) Any one of the Control Messages set in PDL CC# is received as a Hi-Hat Control pedal Position Message. The result of receiving the message depends on the parameter of “PDL CTRL”. The SPD-20 receives the message on the basic channel. Hold1 (Controller number 64) Status Second Third BnH 40H vvH n = MIDI channel: 0H–0FH (ch.1–ch.16) vv = Parameter Value: 00H–7FH (0–127) Any one of the Control Messages set in PDL CC# is received as a Hi-Hat Control pedal Position Message. Effects are determined in the PDL CTRL settings. When Hold is selected for the PDL CC# setting, with vv = 40H–7FH, Hold is turned on, and when vv = 00H–3FH, Hold is turned off. This is received via the channel set to the Basic Channel. (4) Program Change Status Second CnH ppH n = MIDI channel: 0H–0FH (ch.1–ch.16) pp = Program number: 00H–62H (0–98) The SPD-20 receives the message on the basic channel. The program change number 0-98 correspond to the patch number 1–99. [Channel Mode Message] (1) Reset All Controllers Status Second Third BnH 79H 00H n = MIDI channel: 0H–FH (ch.1–ch.16) The SPD-20 receives the message on the basic channel. The SPD-20 initializes the controller on receiving this message. Modulation Depth 0 Foot Controller 0 Panpot 0 Expression 0 General Purpose Controller 1 0 General Purpose Controller 2 0 Hold 1 0 [System Real Time Message] (1) Active Sensing Status FEH Whenever the SPD-20 receives this message, it monitors the interval of the coming data....