|
manual abstract
Activating the travel lock Press the on/off button for 3 seconds to enter the travel lock mode (indicated by a rotating key symbol). Wait a few seconds without pressing the on/off button to activate the travel lock. , , 1 2 Replacement Replacement EnglisH 15 3 The motor switches off and the key symbol is visible on the display to indicate that the travel lock has been activated. Note:If you press the on/off button again within a few seconds after entering the travel lock mode, the travel lock will not be activated. Instead, you will have entered one of the two display layout modes. If you want to return to the travel lock mode, press the on/off button two more times until you are back in the travel lock mode (indicated by rotating the key symbol).Then wait a few seconds without pressing the on/off button to activate the travel lock. You can always return to the menu by pressing , the on/off button for 3 seconds. Deactivating the travel lock Press the on/off button for 3 seconds. , The motor starts running to indicate that the shaver has been unlocked.The shaver is now ready for use again. Replace the shaving heads when the shaving unit symbol appears on the display. Replace damaged or worn shaving heads with HQ9 Philips shaving heads only. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. 2 Press the release button to open the shaving unit. 3 Turn the lock anticlockwise (1) and remove the retaining frame (2). 4 Remove the shaving heads and place new ones in the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit (1) and turn the lock clockwise (2). 6 Close the shaving unit. The shaving unit symbol will go out if you keep the on/off button pressed for 3 seconds. Accessories The following accessories are available: HQ8500/HQ8000 powerplug. HQ9 Philips Shaving Heads. HQ110 Philips Shaving Head Cleaning Spray (not available in China). HQ8010 car cord. , --- - 16 English EnglisH 1 Do not throw the appliance away with the , normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this you will help to preserve the environment. The built-in rechargeable battery contains , substances that may pollute the environment. Always remove the battery before discarding the appliance or handing it in at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing the battery, you can also take the appliance to a Philips service centre, which will remove the battery for you and will dispose of it in an environmentally safe way. Disposal of the shaver battery Only remove the battery if it is completely empty. 1 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver. 2 Let the shaver run until it stops, undo the screws and open the shaver. 3 Remove the battery. Do not connect the shaver to the mains again after the battery has been removed. Environment 1 EnglisH Guarantee & service Troubleshooting If you need information or if you have a problem, please visit the Philips website at or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. 1 Reduced shaving performance -Cause 1: the shaving heads are dirty.The shaver has not been rinsed long enough or the water used was not hot enough. -Clean the shaver thoroughly before you continue shaving. See chapter ‘Cleaning and maintenance’. -Cause 2: long hairs are obstructing the shaving heads. -Clean the cutters and guards with the brush supplied. See chapter ‘Cleaning and maintenance’, section ‘Every six months: shaving heads’. -Cause 3: the shaving heads are damaged or worn. -Replace the shaving heads. See chapter ‘Replacement’. 2 The shaver does not work when the on/off button is pressed. -Cause 1: the shaving heads are dirty. -Recharge the battery. See chapter ‘Charging’. -Cause 2: the appliance is not connected to the mains. -Put the powerplug in the wall socket. EnglisH 19 3 The shaving unit has come off the shaver. -Cause: the shaving unit has not been placed correctly. -If the shaving unit becomes detached from the shaver, you can easily reattach it (‘click’). 4 The display shows the word CHECK and a blinking shaving unit symbol and tap unit symbol. -Cause 1: long hairs and dirt are obstructing the shaving heads. -Clean the shaver thoroughly before you continue shaving. See chapter ‘Cleaning and maintenance’. -Cause 2: the shaving heads are damaged or worn. -Replace the shaving heads. See chapter ‘Replacement’. 20 Penting indonEsia 20 Penting indonEsia Bacalah petunjuk penggunaan ini dengan saksama sebel...
Other models in this manual:Musical Instruments - HQ9170 (5.48 mb)
Musical Instruments - HQ9171 (5.48 mb)
Shavers - HQ9170/16 (5.48 mb)
Shavers - HQ9170/21 (5.48 mb)