Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
This means that a separate power supply is not needed to use the product with the power systems found in most countries. You should always use the power supply that shipped with your Aviom product. When travelling, you may need plug adapters to use the power supply with the AC outlet plug shape variations in use throughout the world. Should you need to replace the power supply that came with your product, we recommend using only a power supply that meets the following specifications. Type: Input Voltage: Output: Polarity _ Switching 50/60Hz 90-240 volts 30VA 24Vdc 0.5A Outer = negative; Inner = positive + Power Supply Polarity Note that polarity of the plug found on the DC power supply needs to match that of the original power supply that came with your Aviom equipment. Aviom products use a center positive power supply. The outer contact is negative, the inner contact is positive. (See the diagram above.) Aviom A-16R and A-16CS User Guide Cleaning and Maintenance The exterior of your Aviom products should be cleaned with a dry, soft, lint-free cloth. For tougher dirt, you can use a cloth slightly dampened with water or with a mild detergent. When cleaning your Aviom products, never spray cleaners directly onto the product surfaces. Instead, spray a small amount of the cleaning solution onto a clean cloth first. Then use the dampened cloth to clean the product. Note: Never use solvents or abrasive cleaners on the finished surfaces of your Aviom products. System Setup Start with all devices turned off. When all power and audio connections have been made, you can then power up all the components in your system. AC Power Connection The component parts of your Personal Monitor Mixing System use separate external power supplies. • Connect the power supply to the 18-24 VDC Power jack on the rear of the analog input module (does not apply when using the Yamaha-compatible Y1 card). • Plug the power supply into an available AC power outlet. • Connect the power supply to the A-16R Personal Mixer unit. • Plug the power supply into an available AC power outlet. The Personal Monitor System will be in its “on” state as long as it is plugged into a working electrical outlet. No on/off power switches are included. If you would like to control the power state of your units, simply connect the power supplies to a power strip with an on/off switch. Use that as a system power switch. Note: The A-16CS gets its power from the A-16R when the A-Control jacks are connected via a Cat-5 cable. No power supply is required. System Interconnections A single Category 5 cable is required to connect each A-Net compatible device in your system. Connect a Category 5 cable from the front panel A-Net jack on the Aviom A-Net input module (AN-16/i, AN-16/i-M, A-16T, or Y1 card) to the A-Net In jack on the first Personal Mixer. Connect additional A-16, A-16II or A-16R Personal Mixers with a single Category 5 cable from the A-Net Out jack on the first Mixer to the A-Net In jack on the next Personal Mixer. (Repeat this process for Aviom A-16R and A-16CS User Guide each additional Mixer unit in your system.) As an option, you can use the A-16D or A-16D Pro A-Net Distributors for parallel connections. If using the A-16CS Control Surface for remote mix control, patch a Cat-5 cable from the A-16R A-Control jack to the A-Control input on the A-16CS. Audio Connections — Inputs The Aviom Personal Monitor Mixing System is designed to work in a wide variety of audio situations. For complete setup information, refer to the detailed instructions included with your A-Net input module. Line outputs, aux sends, direct outputs, bus and group outputs are some examples of signals that are compatible with the analog inputs of Aviom’s input modules. Users of the Y1 card with Yamaha digital mixing consoles can patch audio to the A-Net channels in the digital domain using the Yamaha mixer’s user interface. Audio Connections — Outputs Plug headphones or in-ear monitors into the A-16R Personal Mixer’s front panel Headphone jack. If you use powered stage monitors, spot monitors, or wireless in-ear monitors, connect the Line output jacks on the rear panel of the A-16R Personal Mixer to the inputs of your audio device. Before powering up the system, turn the Master Volume control on the Personal Mixer to its minimum setting (full left) to ensure that unwanted high-volume audio is not accidentally sent into your monitors when the system is powered up. The Master Volume control is on the right side of the Personal Mixer, next to the Bass and Treble controls. If you are using the A-16CS Control Surface, make sure that the A-Control cable is connected and that the REMOTE/LOCAL switch on the front panel of the A-16R is in the REMOTE position. Labeling the Channels The A-16R Personal Mixer and the A-16CS Control Surface have a convenient label strip right on the front panel. Use a china marker (sometimes called a “grease pencil”) to write the name of the instrument or audio source...
Other models in this manual:Musical Instruments - A-16R (1.97 mb)