Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
THE ENCLOSURE WHEN THE POWER SWITCH IS IN THE OFF POSITION. Tremolo Speed (3) The speed control determines the rate at which the signal is modulated. This control varies the speed of the Tremolo master oscillator and should provide any speed desired for modern music. Clockwise rotation of the speed control increases the speed of the modulation of the tremolo. The Tremolo feature is defeatable from a remote footswitch. Tremolo Intensity (4) The intensity control is used to vary the amount of amplitude modulation of the clean signal. It can be adjusted from barely perceptible to dramatic modulation. Clockwise rotation of the intensity control increases the depth of the tremolo. Effects Return (5) Input for returning signals to external effects or signal processing equipment. Effects Send (6) Output for supplying signal to external effects or signal processing equipment. Treble, Middle AND Bass EQ (7) Passive tone controls that regulate high, mid, and low frequencies, respectively. Boost Switch (8) Boosts the overall system gain. Depress to the "in" position to activate. Reverb (9) Reverberation is an echo effect. Rotate clockwise to increase the effect. Post Gain (10) Controls the overall volume level of the Lead channel. The final level adjustment should be made after the desired sound has been activated. Pre Gain (11) Controls the input volume level of the Lead channel. Channel Select Switch (12) Allows selection of the Lead or Normal channel. Note: Channel selection may also be achived by the remote footswitch. If remote selection is desired, the channel switch must be in the "in" (Lead) position. 8 Front Panel 1314 Normal Gain (13) Controls the volume level of the Normal channel. Input (14) The input jack will accept signals from all types of guitar pickups. Be sure to use a high-quality shielded cable to connect the guitar to the amplifier. 1516Rear Panel External Speaker Jack (15) Provided for the connection of external speaker cabinet. Minimum total impedance is 16 ohms. Remote Switch Jack (16) Provided for the connection of the optional remote footswitch. Footswitch is used to select the Lead or Normal channels and defeat tremolo. When using remote footswitch, always insert the plug fully (second click) to ensure proper operation. 9 Delta Blues™ Guitar Amplifier SPECIFICATIONS POWER AMPLIFIER SECTION Four 6BQ5/EL84’s with 12AX7 driver Rated Power & Load: 30 watts RMS into 16 or 8 ohms Power @ Clipping (Typically): (5% THD, 1 kHz, 120 V AC line) 30 watts RMS into 16 or 8 ohms (Bias must be reduced to measure) Frequency Response: +0, -2 dB, 50 Hz to 15 kHz, @ 20 watts RMS into 16 ohms Hum & Noise: Greater than 80 dB below rated power Power Consumption: 150 watts, 50/60 Hz, 120 VAC (Domestic) PREAMP SECTION Two 12AX7’s The following specs are measured @ 1 kHz with the controls preset as follows: Pre & Post (lead) @ 0 Reverb Level @ 0 Bass & Treble EQ @ 12 Middle EQ @ 0 Channel Select Out Boost Switch Out Nominal level is with Input Gain @ 6. Minimum level is with Input Gain @ 12. Preamp Normal Input: Impedance: Very high Z, 470 K ohms Lead Channel (Post Gain @ 12): Nominal Input Level: -40 dBV, 10 mV RMS Minimum Input Level: -70 dBV, 0.3 mV RMS Normal Channel: Nominal Input Level: -17 dBV, 140 mV RMS Minimum Input Level: -28 dBV, 40 mV RMS Maximum Input Level:0 dBV, 1.0 V RMS Equalization: (Lead and Normal Channels) Custom bass, middle, and treble passive-type EQ Effects Send: Load Impedance: 1 K ohm or greater Nominal Output Level: -6 dBV, 0.5 V RMS Effects Return: Impedance: High Z, 2 M ohms Designed Input Level: -6 dBV, 0.5 V RMS (Switching jack provides Effects Send to Effects Return connection when not used.) External Footswitch Function: Normal/Lead Channel Select (when Lead activated) Tremolo Defeat 10 TONE SETTINGS ROCK CHANNEL BOOST ADJUST TO "IN" "OUT" TASTE METAL ADJUST TO TASTE ADJUST TO TASTE ADJUST TO TASTE BLUES COUNTRY CHANNEL "IN" CHANNEL "OUT" IN FOR LEAD CHANNEL "OUT" IN FOR LEAD BOOST "OUT" BOOST "OUT" BOOST "OUT" 11 PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: September 5, 2007 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer. Who This Warranty Protects This Warranty protects only the original retail purchaser of the product. How Long This Warranty Lasts The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows: Product Category Duration Guitars/Basses, Amp...