Votes - 2, Average rating: 4
(
)
)
|
manual abstract
THE WORLD’S BEST KITS.™ © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION 1-800-221-0932 metraonline.com 95-7951 95-7951 Applications Chevrolet Suzuki Pontiac Aveo 2004-2006 Forenza 2004-2008 G3 Hatchback 2007 Aveo Hatchback 2007-2008 Reno 2005-2008 Verona 2004-2006 Table of Contents Dash Disassembly – Chevrolet Aveo 2004-2006 3 – Chevrolet Aveo Hatchback 2007-2008 3 – Pontiac G3 Hatchback 2007 3 – Suzuki Forenza 2004-2008 4-5 – Suzuki Reno 2005-2008 4-5 – Suzuki Verona 2004-2006 6 Kit Assembly – Double DIN radio provision 7-8 – Stacked ISO mount units provision 9-10 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. *NOTE: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected Metra recommends MECP mobile electronics school in our industry. Log onto or call certified technicians 800-354-6782 for more information and take steps toward a better tomorrow. Dash Disassembly 95-7951 Dash Disassembly 95-7951 Chevrolet Aveo 2004-2006 Chevrolet Aveo Hatchback 2007-2008 Pontiac G3 Hatchback 2007 1. Unclip and remove the trim panels from both sides of radio/climate controls. (Figure A) 2. Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) Continue to kit assembly (Figure A) (Figure B) 3 Dash Disassembly 95-7951 Dash Disassembly 95-7951 Suzuki Forenza 2004-2008 Suzuki Reno 2005-2008 1. Disconnect air selector cable on driver’s side of center console behind dash above accelerator pedal. (Figure A & B) 2. Open glove box and remove (5) Phillips screws ((3) on top and (2) on bottom) then remove entire glove box. 3. Disconnect temperature selector cable on passenger side of center console behind glove box. (Figure C) Continued on next page (Figure A) (Figure B) Inside of Glove Box (Figure C) 4 Dash Disassembly 95-7951 Dash Disassembly 95-7951 Suzuki Forenza 2004-2008 Suzuki Reno 2005-2008 4. Unsnap and remove entire panel surrounding radio. NOTE: The clips holding radio panel to dash are very strong. (Figure D) 5. Remove (4) 10 mm bolts securing radio. Unplug and remove radio. (Figure E) Continue to kit assembly AM/FMTAPECDTUNE123456BASSMUTEEQASTSCAN(Figure D) (Figure E) 5 Dash Disassembly 95-7951 Dash Disassembly 95-7951 Suzuki Verona 2004-2006 1. Unclip and remove the trim panel surrounding the radio. (Figure A) 2. Remove (4) Phillips screws from radio. Unplug and remove radio. (Figure B) Continue to kit assembly (Figure A) (Figure B) 6 7 Kit Assembly 95-7951 Double DIN radio provision NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007- 08, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-06, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-08 and the Suzuki Reno 2005-08, cut the rear lower mounting tabs (Figure B). NOTE: The Verona 2004-2006 sub dash will need to be trimmed slightly for proper fit. Refer to illustration. (Figures C and D) Continued on next page CUT HERE ON BOTH SIDES (Figure C) (Figure D) (Figure B) (Figure A) Kit Assembly 95-7951 Kit Assembly 95-7951 Double DIN radio provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure E) 3. Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure F) 4. Reassemble dash in reverse order of disassembly. (Figure E) (Figure F) 8 9 Kit Assembly 95-7951 Stacked ISO mount units provision NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007- 08, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-06, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-08 and the Suzuki Reno 2005-08, cut the rear lower mounting tabs (Figure B). NOTE: The Verona 2004-2006 sub dash will need to be trimmed slightly for proper fit. Refer to illustration. (Figures C and D) Continued on next page CUT HERE ON BOTH SIDES (Figure C) (Figure D) (Figure B) (Figure A) Kit Assembly 95-7951 Kit Assembly 95-7951 Stacked ISO mount units provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure E) 3. Slide the stacked ISO units into the bracket/trim plate assembly and secure the units to the assembly using...