Login:
Votes - 3, Average rating: 4.7 ( )

User manual Metra Electronics, model 99-7319

Manafacture: Metra Electronics
File size: 741.39 kb
File name: INST99-7319.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


1,2 Kit Assembly ....................................... 3,4 Final Assembly 99-7319 DASH DISASSEMBLY 2004-2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove panel surrounding shifter including cup holders. (Figure A) 3 Remove (2) Phillips screws at base of panel surrounding radio and a/c controls. (Figure B) 4 Unclip and remove panel surrounding radio and a/c control. (Figure C) KIA AMANTI A 1 99-7319 DASH DISASSEMBLY 2004-2006 KIA AMANTI D 5 Remove (6) Phillips screws securing radio and a/c control. (Figure D) 6 Remove (4) Phillips screws securing factory a/c control to bracket assembly. (Figure E) 2 Phillips screws on each side E 2 99-7319 KIT ASSEMBLY 2004-2006 KIA AMANTI DIN HEAD UNIT PROVISION 1 Attach the corresponding a/c control bracket to the factory a/c control using the factory hardware. (Figure A) Note: The radio housing must be installed first before the a/c control. 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure B) 2 Slide the aftermarket head unit into the cage and secure. (Figure C) 3 99-7319 KIT ASSEMBLY 2004-2006 KIA AMANTI ISO DIN HEAD UNIT PROVISION A 1 Attach the corresponding a/c control bracket to the factory a/c control using the factory hardware. (Figure A) Note: The radio housing must be installed first before the a/c control. 1 Mount the ISO bracket to the head unit with screws supplied with the unit. (Figure B) 2 Slide the head unit into the radio opening until the side clips engage. (Figure C) 3 Snap the trim plate into the radio housing. (Figure C) B C 4 99-7319 FINAL ASSEMBLY ÊÙlü/nhS A B D FINAL ASSEMBLY A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly installing the radio housing first and then the a/c control. FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . Red Right Front (+) Gray 12V Batt / Memory. . Yellow Right Front (-) Gray / Black Ground.......... Black* Left Front (+) White Power Antenna Blue Left Front (-) White / Black Amp Turn-On Blue / White Right Rear (+) Violet Amp Ground Black / White Right Rear (-) Violet / Black Illumination....... Orange Left Rear (+) Green Dimmer......... Orange / White Left Rear (-) Green / Black *NOTE: When Black a wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 5 99-7319 INSTRUCTIONS a 1-800-221-0932 Ü REV. 06/19/2007 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-7319...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category