Votes - , Average rating:
(
)
)
Manafacture: American Audio
File size: 2.33 mb
File name: XDM250T.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
A yellow LED above the power switch will glow to indicating power is ON. Be fore you turn the power on be sure you have made all connections to the mixer. Also be sure you amplifier are tuned off. Remember mixer on first and turned off last. 20. Power Supply Jack - This connection is used for your detachable AC power cord. Only connect a recommended power supply of AC 9v~12v, 500mA. Use of a power supply other than the recommend power supply may damage your unit and will void your manufactures warranty. 21. Master Output Connectors - These RCA jacks send a low current unbalanced output signal. 22. Channel2 Line Input Jacks - Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Do not connect turntables to these jacks, turntables should only be connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the white jack represents the left channel input. 23. Channel2 Phono Input Jacks - Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). The red colored RCA jack represents the right channel input and the white represents the left channel input. 24. Channel2 Ground - Connect a turntable ground lead to this terminal. This will reduce the humming and popping noises associated with magnetic phono cartridges. 25. Channel2 Line Input Jacks - Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Do not connect turntables to these jacks, turntables should only be connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the white jack represents the left channel input. 26. Channel2 Phono Input Jacks - Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). The red colored RCA jack represents the right channel input and the white represents the left channel input. ©American Audio® XDM-250T™ Instruction Manual Page 6 XDM-250T™ Typical Mixer Set-Up aj_l POWER SOURCE: AC 10 CCB L NE 2 F CASSETTE DECK A m t n I 0 M t ■ w à % TURNTABLE Á m I 0 t ■ « TURNTABLE ©American Audio® - - XDM-250T™ Instruction Manual Page 7 XDM-250T™ Typical Mixer Set-Up XDM-25QT FEATHER FADER plus -fff jNNj PROformer/aÆ» ® ® ® ® © /(o) © © I © © LINE 2 PHONO 2 I LINE 1 PHON01 CH-2 —' V— CH-1 —' RCA to 1/4” Patch Cables Speaker Cables ©American Audio® - - XDM-250T™ Instruction Manual Page 8 XDM-250T™ Cleaning Due to fog residue, smoke, and dust, cleaning the mixer should be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a cleaner specially designed for electronics to spray in and around the knobs and switch. This will reduce small particle built up that can effect the proper operation of the mixer. 3. Clean should be carried out every 30-60 days. 4. Always be sure to dry all parts completely before plugging the mixer in. Cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue, dust, dew). XDM-250T™ Cross Fader Replacement The crossfader is “Hot Swappable” which means it may be replaced at any time, even when power is applied. Only replace with American Audio Feather Fader Plus. Replacing with any other model fader may seriously damage your mixer. Replacing the Crossfader: 1. Disconnect the mixers main power supply 2. Using a number two Phillips screw driver, unscrew the each of the stainless steel retain screws that hold the crossfader in place. 3. Gently remove the crossfader from its seated position. You may need to wiggle the crossfader slightly to remove it. 4. After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the actual cables. The connector is desired to only fit one way, so don’t worry about the connectors orientation. 5. Connect the new crossfader to the ribbon cable and replace in reverse order. ©American Audio® XDM-250T™ Instruction Manual Page 9 XDM-250T™ Warranty The XDM-250T™ carries a two year limited warranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a R.A.(return authorization) number. If the mixer is under warranty, you must provide a proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on out toll free number. XDM-250T™ Main Features 2-YEAR LIMITED WARRANTY A. American Audio® hereby warrants, to the original purchaser, Ameri...