Votes - 3, Average rating: 4
(
)
)
|
manual abstract
The signal is then controlled via the CH-1 and CH-2 faders (4). • The XDM-343 features three microphone inputs. The Canon Mic 3 jack (10) on the front panel is for 1/4” (6.3mm) jack plugs and XLR-plugs. With the TALKOVER switch (1 1), you can attenuate all other signals without affecting the microphone volume. The XDM-343 also features two more 1/4 inch (6.3mm) Mic jacks (27, 28) on the rear panel. You can adjust the microphone volume using the CHANNEL faders. Make sure that the respective PHONO / LINE / MIC switch is set to MIC. • You can connect 2 record players using the PHONO 1 jacks (18) and PHONO 2 jacks (19) on the rear panel. You can only control the record player signal after you switched the PHONO / LINE / MIC switches (5) to PHONO. The signal is then controlled via the CH-1 and CH-2 faders (6). If you wish to connect a third record player, switch the LINE 3 / PHONO 3 SELECTOR (29) on the rear panel to PHONO 3. You can only control the record player signal after you switched the PHONO 3-LINE 3 / LINE 4 / MIC 3 switch (5) to PHONO 3. The signal is then controlled via the CHANNEL 3 fader (6). • Connect your tape recorder, tuner, sound effects, CD player, cassette deck or any other line signals to the AMP OUTjacks (18, 19 & 20) on the rear panel. You can only control the line signals after switching the PHONO/LINE/MIC switches (5) to LINE. The signal is then controlled via the CH-1, CH-2 and CH-3 faders (6). © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-343 User Instructions page 2 Functions 110 11 12 13 14 2 5 6 7 8 9 15 17 16 34 110 11 12 13 14 2 5 6 7 8 9 15 17 16 34 (1) POWER SWITCH (2)MASTER LEVEL / PFL DISPLAY -The upper display shows the level of the left and right master output. The lower display shows the level of the channel currently being cued (PFL LED on). (3) GAIN CONTROL -Used to set the level of the input signal. (4) BASS/MIDDLE/TREBLE CONTROL - Used to increase or decrease the LOW’s, MIDs, and HIs of the input signal. (5) PHONO / LINE I MIC SWITCH -Used to select the input to be sent to the individual channel. Channel 1 and 2 can be switched phono/line/mic. Channel 3 can either be switched line/line/mic or phono/line/mic. The selector is on the rear panel. (6) CHANNEL FADER - Used to adjust the input level of each channel. (7) PFL/CUE BUTTONS - Use the PFL/CUE button to adjust the input level of each channel. (8) BEAT INDICATOR CHANNEL I / CHANNEL 2 - The LED lights up at every bass beat of the respective source. As soon as the LEDs blink synchronously, the speed of the two sources is synchronized. (9) CROSSFADER - Mixes the signals of channel 1 and channel 2. When the crossfader is set in the center position, both channels can be heard at once. (10) MIC 3 JACK -You can connect microphones with 1/4 inch (6.3mm) jack plug or XLR-plug. (11) TALKOVER BUTTON - Press the talkover button when you want to use the microphone. When the button is pressed, all signals except the microphone level are decreased by 15dB. In the OFF position, all signals return to their original level. When talkover is ON, the red L.E.D. is lit. NOTE: The TALKOVER button only works with the microphone plugged into MIC 3 JACK. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-343 User Instructions page 3 Functions (Cont.) (12) CUE MIXING CONTROL -Selects the channel for monitoring. The monitor signal comes from Prefader. This means it will not be affected by the channel faders. You can monitor every channel individually and all possible combinations. Connect your headphones to the HEADPHONES jack (14). Turn the CUE MIXING CONTROL to CUE and select the desired channels with the PFL switches (7). When you turn the CUE MIXING CONTROL to PGM (PFL switches without function), you can cue the output signal of the mixer. If the CUE MIXING CONTROL is set to the center position, you can cue both the channel signal you selected and the output signal. With the CUE LEVEL control (I3), you can adjust the phones volume without changing the output signal. (13) CUE LEVEL CONTROL -Adjusts the headphone output level. (14) HEADPHONES JACK -Use this jack to connect the headphones. Headphones from 8 Ohms to 600 Ohms can be used. 16 Ohms is recommended. (15)BOOTH LEVEL CONTROL -The XDM-343 features a DJ BOOTH monitor system. Connect your monitor system with the BOOTH OUT jacks (22) on the rear panel. (16) BALANCE CONTROL -Used to adjust how much of the signal is sent to the left and right MASTER OUT jack (23). (17) MASTER CONTROL -Adjusts the level of the master output. Inputs and Outputs 29 2728 LINE 1 CH 1 PHONO 1LINE 2 CH 2 PHONO 2LINE 4 CH 3 LINE 3 PHONO 3 MASTER OUTPUT BOOTH REC L - R - GNDMIC 1 AC IN 115 / 230V ACVOLTAGE SELECTOR FUSE 115 26 202122 MIC 2 LINE 3 PHONO 3 19 25 19 18 24 (18), (19), (20) LINE I PHONO INPUT JACKS -Input jack for CH-1, CH-2 and CH-3- Connect turntables equipped with MM pickup cartridge to PHONO input. C...