Votes - 2, Average rating: 4
(
)
)
|
manual abstract
6. After all the units settings have been set and are plugged in, adjust the sensitivity knob on the bottom of the master unit to make them react to sound. 7. To run a synchronized light show set all the dipswitch on all the fixture to the ‘off’ position. All fixtures will now run in the same exact pattern. 8. You can also use the optional MINI/C Remote Control. If you want to use the optional remote control, connect the MINI/C controller to the first fixture in the line (master). Note: The remote control only operates in Stand-Alone and Master/ Slave modes. If the remote is connected in DMX mode it will not function. If the units do not receive an active DMX signal, the units will automatically react to sound in the Master/Slave mode. DMX Mode: This fixture will react with DMX operation. For best results use only one motor function for each scene (or step), when programming scenes into a DMX controller. This will give you faster mirror and faster gobo/color changes. For Example: A. With the DMX controller move the mirror up then program the step. B. Move the mirror down then program that step. C. Change the gobo/color wheel then program that step. D. Continue this pattern to achieve best results. 1. Operating through a DMX controller gives the user freedom to create his/her own programs tailored to their own individual needs. This function also allows you to use your fixtures as spots. 2. This operation will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the Elation® Show Designer™ or the Elation® DMX Operator.™ 3. The DJ Scan 250HP™ uses four DMX channels to operate; Channel1 is Pan, channel 2 is Tilt, channel 3 is Color, and channel 4 Gobos. 4. To run your fixture in DMX mode, plug in the fixture via the XLR ©American DJ Supply® -- DJ Scan 250HP™ User Manual Page 8 DJ Scan 250HP™ Lamp Replacement DJ Scan 250HP™ Operating Instructions DJ Scan 250HP™ Lamp Replacement DJ Scan 250HP™ Operating Instructions the on position - Follow the set-up specifications that come with the controller. DJ Scan 250HP™ Optional Remote The MINI/C controller may be purchased separately allowing you to control the main unit, and any others connected to it, while it is in stand alone mode. You can set the unit to blackout. If you have more than one unit, make sure the remote control is plugged into the first unit in the daisy chain. The remote control will not have any effect if the unit is in DMX mode. When the unit is in blackout mode, the light will come on next to the blackout button. The DJ Scan 250HP™ may be controlled by a wide range of controllers; ie. Show Designer™, DMX Operator,™ Scene Setter™ or by the DJ MINI/C basic controller. MINI/C features: 30 ft. cable Stand by (Black out) Lamp Replacement: Caution! Never open the unit when in use. Always disconnect the main power before attempting to replace the lamp. 1. Be sure to follow the proper procedures when handling halogen bulbs. 2. Lamp replacement has been made simple by incorporating the use of a removable lamp tray and thumb screws. 3. Loosen the thumb screw on rear cover. 4. Remove the tray. 5. Remove and replace the bulb. 6. Reassemble. Remember to always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized American DJ service technician. DJ Scan 250HP™ Focusing 1. To focus a DJ Scan 250HP,™ it is best to first turn down the music sensitivity knob to its minimum position. 2. Loosen the thumb screw on the front of the unit that hold the lens in place. 3. Adjust the focus by manually moving the lens up and down. 4. Tighten the thumb screw after you achieve your desired focus. ©American DJ Supply® -- DJ Scan 250HP™ User Manual Page 9 ©American DJ Supply® -- DJ Scan 250HP™ User Manual Page 10 DJ Scan 250HP™ Trouble Shooting Cont. DJ Scan 250HP™ Cleaning DJ Scan 250HP™ Trouble Shooting Cont. DJ Scan 250HP™ Cleaning nal optical lenses must be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the out- side casing. 2. Use a brush to wipe down the fan grill. 3. Clean the external optics with glass cleaner and a soft cloth every 20 days. Situation may very. If used heavily in clubs with lots of fog, cleaning may be required more often. 4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days. 5. Always be sure to dry all parts completely before plugging the unit in. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew). DJ Scan 250HP™ Trouble Shooting Listed below are a few common problems the user may encounter, with solutions. No light from the unit; 1. Check if the fan is running. If not, there is no main power supply. 2. Check the breaker in the back panel. 3. Check if lamp is lit. The user should be able to see some light escape through the fan. If power is present but the lamp is not...
Other models in this manual:Musical Instruments - 250HP (1.12 mb)