Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. 4. Place mix station in an appropriate position for operation. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into AC power. 9. Switch everything on in the following order. • audio input sources (i.e. turntables or CD players) • KMX01 • last, any amplifiers or output devices 10. When turning off, always reverse this operation by, • turning off amplifiers • KMX01 • last, any input devices 11. Go to for product registration. More information about this product may be found at REAR CONNECTIONS 1. Channel Inputs: Unbalanced RCA jacks for connecting external sources. The Phono/Line input is selected using the toggle switch on the front panel. Turntables, HiFi VCRs, cassette and reel- to-reel tape decks, DAT machines, CD players, laser discs, tuners, even synthesizers or other mixing consoles can be connected using these jacks. NOTE: Plug mono audio sources into both left and right inputs using a “ Y” cable connector. 2. GND: This screw connector should be used to connect any turntables or other devices that need to be grounded. 3. Input Selector Switch: Use this to allow either line level or phono level equipment to be plugged into your channel inputs. When Phono input is selected, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and will sound very bad, so always be sure to toggle the line/phono switch over to line before connection of line sources. 4. Video OUTPUT: There are two outputs that are connected to television monitors to output karaoke text. 5. Master Output (RCA): This output is for connecting an external monitoring device such as a PA system, powered monitors, or a home stereo. The level of the master stereo output signal is controlled by the master fader. 6. Stereo Balanced Master Outputs (XLR): low- impedance XLR type connectors controlled by the Master fader. 7. Microphone 2 and 3 Input: Plug in your .” microphones into 2 and 3. These inputs have effects available on the face panel. 8. AC In: This mix station is designed to work with the power supply cord that comes with the unit. While the power is switched off, plug the power supply into the mix station first, then plug it into the outlet. 9. Power Switch: Use this switch to turn on the mix station after all input devices are already connected to prevent damage to your equipment. Turn the station on before you turn on amplifiers and turn off amplifiers before you turn off the mix station. 10. NTSC/PAL Switch: Selects the video output between NTSC and PAL video modes. NTSC is used in the United States, while PAL is used in much of Europe. 3 4 FRONT PANEL FEATURES 1. DJ Mic 1: This section has the gain and tone controls for the .”/XLR combination mic input. 2. Mic 2: This section has the gain and tone controls for Mic 2 3. Mic 3: This section has the gain and tone controls for Mic 3 4. Mic 2&3 Echo: This knob controls the echo effect amount on microphones 2 and 3. 5. Mic 2&3 Delay: This knob controls the delay time of the echo effect on microphones 2 and 3 6. Line Faders: Control volume levels in the mix. 7. Master Fader - Controls the overall output level. 8. Input toggle switch - Selects which source will be live to that channel based on what you have connected to the rear panel input section 9. Replaceable Crossfader - This slide fader blends audio between channels 1 and 2. This also switches the video when using compatible karaoke CD+G CDs. Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large screws which hold it in place, lift it out and disconnect it’s cable. Reattach the new crossfader and screw the mounting plate back onto the unit - you’re back in business! 10. Fader Start – Activation allows you to start the CD players from you crossfader. Travel from left to right will start the right CD player and pause the left CD player 11. LED METER - Indicates the Master output level. 12. Stereo/Mono toggle - Changes the Master output between Mono and Stereo 13. Master EQ Bass 14. Master EQ Middle 15. Master EQ Treble 16. Channel Cue Selector - Used to route channel audio to your headphones. 17. Headphone Level – Adjusts cue volume. 18. Headphone Jacks – Used to connect either 1/8” or 1/4” plugs for audio monitoring with headphones. 4 2 83 961 01111 2131415142 83 961 01111 21314151 CD PLAYER FEATURES 1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject the disc. Each press will open or close the disc tray on the transport. NOTE: Tray will not open unles...