Votes - 4, Average rating: 4
(
)
)
|
manual abstract
4 Press . or > on the remote repeatedly until the first track number of the two to be combined appears, then press ENTER/YES on the remote. For example, to combine tracks 4 and 1, select 4. 5 Press . or > on the remote repeatedly until the second track number of the two to be combined appears. Second track number New track to be combined number 6 Press ENTER/YES on the remote. “Complete !” appears. Notes • Tracks recorded in different recording modes (stereo, LP2, LP4 or MONO) cannot be combined. • If both of the combined tracks have track titles, the title of the second track is erased. Undoing the last edit —Undo Function You can use this function to cancel the last edit and restore the contents of the MD to the condition before the edit. Note, however, that you cannot undo an edit if you do any of the following after the edit: • Do another edit. • Press the MD REC z or ENTER/START button. • Update the TOC by turning off the system or ejecting the MD. • Disconnect the power cord. 1 Press MENU/NO on the remote in stop mode to display “Edit Menu.” 2 Press . or > on the remote repeatedly until “Undo ?” appears in the display. “Undo ?” does not appear, when there is no editing function that can be canceled. 3 Press ENTER/YES on the remote. A message appears, depending on the last edit. 4 Press ENTER/YES on the remote again. “Complete !” appears. MD — Editing Changing the recording level after recording —S.F Edit You can change the volume of the recorded tracks using S.F (Scale Factor) Edit. The original track is recorded over at the new recording level. When changing the recording level, you can select Fade-in Recording to gradually increase the signal level at the start of recording, or Fade-out Recording to gradually decrease the signal level at the end of the recording. Changing the overall recording level 1 Press MD on the remote to switch the function to MD. 2 Press PLAY MODE on the remote repeatedly until both “PGM” and “SHUFFLE” disappear. 3 Press MENU/NO on the remote to display “Edit Menu.” 4 Press . or > on the remote repeatedly until “S.F Edit ?” appears in the display, then press ENTER/YES on the remote. 5 Press . or > on the remote repeatedly until “Tr Level?” appears in the display, then press ENTER/YES on the remote. 6 Press . or > on the remote repeatedly to select the track number you want to change the recording level of, then press ENTER/YES on the remote. “Level 0dB” appears. 7 While monitoring the sound, press . or > on the remote repeatedly to change the recording level. The recording level can be adjusted from –12 dB to +12 dB in 2 dB increments. Adjust the recording level so as not to light up “OVER” at the strongest sound. 8 Press ENTER/YES on the remote. “S.F Edit OK?” appears. 9 Press ENTER/YES on the remote. “S.F Edit: **%” appears while the track is being recorded. An amount of time that is roughly equal to or longer than the playback time of the track is required when recording over the track. When the recording finishes, “Complete !” appears for a few seconds. To cancel the operation Press MENU/NO on the remote during step 2 through 8. If you press ENTER/YES on the remote in step 9 and start recording, you cannot interrupt the operation. Fade-in and Fade-out Recording 1 Press MD on the remote to switch the function to MD. 2 Press PLAY MODE on the remote repeatedly until both “PGM” and “SHUFFLE” disappear. 3 Press MENU/NO on the remote to display “Edit Menu.” 4 Press . or > on the remote repeatedly until “S.F Edit ?” appears in the display, then press ENTER/YES on the remote. 5 Press . or > on the remote repeatedly until “Fade In?” or “Fade Out?” appears in the display, then press ENTER/YES on the remote. 6 Press . or > on the remote repeatedly to select the track number you want to Fade-in or Fade-out, then press ENTER/YES on the remote. “Time 5.0s” appears. 7 While monitoring the sound, press . or > on the remote repeatedly to change the Fade-in, or Fade-out recording time. The system plays the portion that will be recorded over using the Fade-in or Fade-out Recording. You can set the time at any value between 1.0 second and 15.0 seconds in 0.1-second increments. You cannot set the time longer than the track. 8 Press ENTER/YES on the remote. “S.F Edit OK?” appears. 9 Press ENTER/YES on the remote. “S.F Edit: **%” appears while the track is being recorded. When the recording finishes, “Complete !” appears for a few seconds. To cancel the operation Press MENU/NO on the remote during step 2 through 8. After recording starts in step 9, you cannot interrupt the operation. Notes • You can not use the S.F Edit Function for tracks recorded in MDLP mode. • You can not undo the S.F Edit Function even if you use the Undo Function. • Do not disconnect the power cord or move the system while recording is in progress. This may damage the recording data, preventing recording from being performed properly. • Do not use an MD that is damaged or dirty, this may prevent data from being recorded p...