Votes - 3, Average rating: 4.3
(
)
)
|
Other manuals for this model:
manual abstract
• Be sure to connect both left and right surround speakers. Otherwise, the sound will not be heard. 2 Connect the FM/AM antennas. Set up the AM loop antenna, then connect it. Jack type A Extend the FM lead antenna horizontally. AM loop antenna FM75 AM 4 Connect the power cord to a wall outlet. The demonstration appears in the display. When you press , the system turns on and the demonstration automatically ends. If the supplied adapter on the plug does not fit your wall outlet, detach it from the plug (only for models equipped with an adapter). To connect optional AV components See page 44. To deactivate the demonstration When you set the time (Step 2: Setting the time), the demonstration is deactivated. To activate/deactivate the demonstration again, press DISPLAY (for MHC-RXD8/ RXD8S) or DEMO (STANDBY) (for MHC-GRX80J/GRX80/R880) while the system is off. Jack type B Extend the FM lead antenna horizontally. FM75 AM COAXIAL AM loop antenna continued Step 1: Hooking up the system (continued) To attach the front speaker pads Attach the supplied front speaker pads to the bottom of the speakers to stabilize the speakers and prevent them from slipping. Step 2: Setting the time You must set the time before using the timer functions. The clock is on a 24-hour system for the Inserting two size AA (R6) batteries into the remote }} ] ] Tip With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones. Note European and Russian models, and a 12-hour system for other models. The 24-hour system model is used for illustration purposes. 1 2,4 3,5 DISPLAY If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage. 1 Press CLOCK/TIMER SET. The hour indication flashes. When carrying this system Do the following to protect the CD mechanism. 1 Press FUNCTION repeatedly until “CD” appears in the display. 2 Turn the jog dial to set the hour. 2 Hold down LOOP and press so that “LOCK” appears in the display. 3 Press ENTER/NEXT. The minute indication flashes. 4 Turn the jog dial to set the minute. 5 Press ENTER/NEXT. The clock starts working. Tip If you’ve made a mistake, start over from step 1. To change the time The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following: 1 Press CLOCK/TIMER SET. 2 Turn the jog dial to select SET CLOCK. 3 Press ENTER/NEXT. 4 Perform steps 2 through 5 above. Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. Step 3: Presetting radio stations You can preset the following number of stations: – 2 band model: 20 for FM, 10 for AM. – 3 band model: 20 for FM, 10 for MW, and 10 for SW, or 20 for FM, 10 for AM, and 5 for UKV, depending on the model you purchased. (Power) Jog dial 43 1 2 continued Step 3: Presetting radio stations (coninued) 1 Press TUNER/BAND repeatedly until the band you want appears in the display. The bands you can receive vary depending on the model you purchased. Be sure to check which bands you can receive. Every time you press this button, the band changes as follows: 2 band model: FM .AM 3 band model: FM nMW nSW To tune in a station with a weak signal Press + or – repeatedly in step 2 to tune in the station manually. To set another station to the exist preset number Start over from step 1. After step 3, turn the jog dial to select the preset number you want to store the other station. You can add a new preset number after the last preset number. To erase the preset station 1 Keep pressing TUNER MEMORY until a preset number appears in the display. n or FM nAM nUKV* n 2 Turn the jog dial to select the preset * “STEREO PLUS” is displayed when you select UKV. 2 Press and hold + or – until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. 3 Press TUNER MEMORY. A preset number appears in the display. The stations are stored from preset number 1. Preset number 4 Press ENTER/NEXT. The station is stored. 5 Repeat steps 1 to 4 to store other stations. number you want to erase. Select “ALL ERASE” when you want to erase all the preset stations. 3 Press ENTER/NEXT. “COMPLETE” appears. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval (Except for the European and Middle Eastern models) The AM tuning interval is factory set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power ...
Other models in this manual:Home Stereos - MHC-R880 (789.5 kb)
Home Stereos - MHC-RXD8S (789.5 kb)