Votes - 1, Average rating: 3
(
)
)
|
manual abstract
Center speaker Front Front speaker speaker (L) (R) Rear Rear speaker 45 speaker (L) (R) 2 Place the center speaker so it is placed at about the same height as the front speakers (A). Align the center speaker with the front speakers or place it a little behind the front speakers’ position (B). A B Center speaker 3 Place the rear speakers facing each other at about 60 to 90 cm above your listening position. Rear speaker 60 to 90 cm continued Step 2: Setting up the speakers (continued) Adjusting the speaker volume To enjoy Dolby Pro Logic Surround sound, adjust the volume of each speaker using the test tone that the system provides. 1 VOLUMEPOWER 1 3 VOLUME +/– 2,4 1 Press PRO LOGIC (or PRO LOGIC ON/OFF on the remote). The indicator on this button lights up. 2 Press T. TONE ON/OFF on the remote. The test tone is heard from the speakers in the following order. Adjust the volume of the test tone. nFront (left) nCenter Rear NFront (right) N 3 From your listening position, press CENTER LEVEL +/– and REAR LEVEL +/– on the remote to adjust the volume levels. The volume levels from each speaker should be the same. 4 Press T. TONE ON/OFF when you are done adjusting. The test tone is turned off. Note The test tone feature works only for Dolby Pro Logic Surround sound. Tip If you turn VOLUME (or press VOLUME +/– on the remote), all the speaker volumes change. 1 Press t/CLOCK SET. Step 3: Setting the The hour indication flashes. time You must set the time before using the timer functions. 1 3,5 2,4 2 Press TUNING +/– to set the hour. The clock uses the 12-hour system. 3 Press ENTER/NEXT. The minutes indication flashes. 4 Press TUNING +/– to set the minutes. 5 Press ENTER/NEXT. The clock starts. Tip If you make a mistake, start over from step 1. Step 4: Presetting radio stations You can preset up to 30 stations, 20 for FM and 10 for AM. 3,5 1 246POWER 1 Press TUNER/BAND repeatedly until the band you want appears in the display. Each time you press this button, the band changes as follows: FM .AM 2 Press TUNING MODE repeatedly until “AUTO” appears in the display. 3 Press TUNING +/–. The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. DISCALL DOLBY NR OFF AUTO TUNED STEREO MHzS 4 Press TUNER MEMORY. A preset number flashes in the display. DISCALL DOLBY NR OFF AUTO TUNED STEREO S 5 Press TUNING +/– to select the preset number you want. DISCALL DOLBY NR OFF AUTO TUNED STEREO S 6 Press ENTER/NEXT. The station is stored. 7 Repeat steps 1 through 6 to store other stations. To tune in a station with a weak signal Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING +/– to tune in the station. To change the preset number Start over from step 1. To change the AM tuning interval (Except for the Middle Eastern model) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To change the AM tuning interval to 10 kHz (or 9 kHz), press TUNER/BAND repeatedly until “AM” appears first, then turn off the system. While holding down ENTER/NEXT, turn the system back on. When you change the interval, the AM preset stations will be erased. To reset the interval, repeat the same procedure. Note The preset stations are canceled when you disconnect the power cord or if a power failure occurs for half a day. Connecting optional AV components To enhance your system, you can connect optional components. Refer to the instructions included with each component for details. Connecting a TV/VCR You can connect a TV and VCR to enjoy Dolby Pro Logic Surround encoded videos and TV programs. Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected TV/VCR, press FUNCTION repeatedly until “VIDEO” appears. To the audio output of the TV/VCR Connecting audio components Connecting a turntable Be sure to match the color of the plugs and the connectors. To listen to the sound from the connected turntable, press FUNCTION repeatedly until “PHONO” appears. To the audio output of the turntable Note Using the turntable at high volume may cause distortion or howling. This is often caused by the bass sound from the speakers. The bass sound may be picked up by the needle of the turntable, and produce the distortion or howling. To avoid this, do the following: 1 Keep some distance between the speakers and the turntable. 2 Stop using the surround effect. 3 Install the speakers or the turntable on a firm and stable surface. 4 Press SUPER WOOFER repeatedly until the indicator on this button goes off. Connecting outdoor antennas Connect an outdoor antenna to improve the reception. FM antenna Connect an optional FM outdoor antenna. You can also use the TV antenna instead. 75-ohm coaxial cable (not supplied) Screw clamp Ground wire (not supplied) AM FM75 AM antenna Connect a 6 to 15 meter insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected. Screw clamp Insulated wire (not ...
Other models in this manual:Home Stereos - LBT-XB8AV (694 kb)