Votes - 3, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
The 24-hour system is used for illustration purposes. lhHSsjJLHSs 1 3,52,4 Tip With normal use, the batteries should last for about six months. When the remote no longer operates 1 Press CLOCK/TIMER SET. the system, replace both batteries with new ones. The hour indication flashes. Note If you do not use the remote for a long period of time, remove the batteries to prevent possible damage from battery leakage. When carrying this system Make sure that all discs are removed from the unit. To protect the CD mechanism, hold down CD and press ?/1while the power is on. “LOCK” appears in the display and the power is turned off. 2 Press .or >repeatedly to set the hour. 3 Press ENTER. The minute indication flashes. 4 Press .or >repeatedly to set the minute. 5 Press ENTER. The clock starts working. Tip If you make a mistake, start over from step 1. To change the time The previous explanation shows how to set the time while the power is off. To change the time while the power is on, do the following: 1 Press CLOCK/TIMER SET. 2 Press .or >repeatedly to select SET CLOCK. 3 Press ENTER. 4 Perform steps 2 through 5 above. Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. Step 3: Presetting radio stations You can preset a total of 30 preset stations (20 for FM and 10 for AM). ?/1 (Power) 23 Shuttle 41 continued Step 3: Presetting radio stations (continued) 1 Press TUNER/BAND repeatedly to select FM or AM. 2 Press and hold + or – (or TUNING +/– on the remote) until the frequency indication starts to change, then release. Scanning stops automatically when a station is tuned in. “TUNED” and “STEREO” (for a stereo program) appear. MHz STEREO TUNED 3 Press TUNER MEMORY. A preset number appears in the display. The stations are stored from preset number 1. Preset number 4 Press ENTER. The station is stored. 5 Repeat steps 1 through 4 to store other stations. To tune in a station with a weak signal Press + or – (or TUNING +/– on the remote) repeatedly in step 2 to tune in the station manually. To set another station to an existing preset number Start over from step 1. After step 3, turn the shuttle until it clicks to select the preset number where you want to store the other station. You can preset a new station in the selected preset number. TUNED STEREO To erase a preset station 1 Press and hold TUNER MEMORY until a preset number appears in the display. 2 Turn the shuttle until it clicks to select the preset number you want to erase. Select “ALL ERASE” when you want to erase all the preset stations. 3 Press ENTER. “COMPLETE” appears. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval (Except for the European and Middle Eastern models) The AM tuning interval is factory-preset to 9 kHz (10 kHz in some areas). To switch the AM tuning interval, tune in any AM station first, then turn off the power. While holding down ENTER, turn the power back on. When you change the interval, AM preset stations are erased. To switch back to the original interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power cord or a power failure occurs. Saving the power in standby mode (MHC-BX3 only) You can lower the power consumption to a minimum (Power Saving Mode) and save energy in the standby mode. DISPLAY ?/1(Power) , Press DISPLAY repeatedly when the power is off. Every time you press the button, the system switches as follows: t Demonstration t Clock Power Saving Mode T The system is turned on/off by pressing ?/1. Tips • ?/1indicator and timer indicator (when the timer is set) light even in the Power Saving Mode. • The timer functions in the Power Saving Mode. Note You cannot set the time in the Power Saving Mode. To cancel the Power Saving Mode Press DISPLAY once to show the demonstration, twice to show the clock display. Basic Operations Basic Operations Playing a CD — Normal Play You can play up to three CDs in a row. DISC SKIP EX-CHANGE hH 1 x VOLUME. > PLAY MODEX 2 ?/1 (Power) j J l L hH H S s Shuttle hH S s l L j J CD VOL +/– 1 Press Z OPEN/CLOSE and place a CD on the disc tray. If a disc is not placed properly, it will not be recognized. Place with the label side up. When you play a CD single (8 cm CD), place it on the inner circle of the tray. To insert a second and third disc, press DISC SKIP EX-CHANGE to rotate the disc tray. 2 Press one of the DISC 1~3 buttons. The disc tray closes and playback starts. If you press hH when CD is selected as the function and the disc tray is closed, playback starts from the CD loaded on the tray whose disc pointer indicator is lit. Disc pointer Track number Playing time indicator Disc presence Disc tray number indicator To Do this Stop playback Press x. Pause Press X. Press again to resume playback. Select a track During play or pause, press > (to go forward) or . (to go back). Find a po...
Other models in this manual:Home Stereos - MHC-BX3 (465.11 kb)