Votes - 1, Average rating: 3 ( )

Manafacture: Philips File size: 1.64 mb File name: Language of manual:

It is not recommended for use in this system. – Store the tapes at room temperature and do not put them too close to a magnetic field (for example, a transformer, TV, or speaker). Dolby B Noise Reduction System 1 Press DOLBY B NR to switch on Dolby B NR. . The d B NR appears in the display. 2 Press DOLBY B NR again to switch off Dolby B NR. . The d B NR disappears from the display. Note: – A tape recorded with the Dolby B NR system should also be played in the Dolby B NR mode. If you forget to operate the DOLBY NR button, the treble may be reproduced too strongly. CD TAPE PROG A.REV TUNER AUX PRESET s s STOP•CLEAR SEARCH • TUNING PLAY • SIDE CD1 • 2 • 3 BAND TAPE 1 • 2 CDR ER 21 English RECORDING INTERACTIVE SOUND STUDIO CD TAPE PROG CLOCK/ TIMER NEWS! RDS STANDBY ON A.REV TUNER AUX PRESET s s STOP•CLEAR SEARCH • TUNING PLAY • SIDE MINI HIFI SYSTEM CD1 • 2 • 3 BAND TAPE 1 • 2 CDR MORE ENTER JOG NEWS/TA RDS/ CD TEXT MAX SOUND MIC MIC LEVEL VOLUME DSC SURF PERSONAL HOLD DBB STROBE VEC PAN SOUND CONTROL DISPLAY MAX VEC DBB DOLBY B NR DUB (HSD) REC Notes: – If you do not intend to record via the microphone, unplug the microphone to avoid accidental mixing with other recording source. – For recording, use only tape of IEC type I (normal tape) or IEC type II (Cr02). – The tape is secured at both ends with leader tape. At the beginning and end of tape, nothing will be recorded for 6 to 7 seconds. – The recording level is set automatically, regardless of the position of Volume, DBB, VEC or DSC. – To prevent accidental recording, break out the tab on the left shoulder of the tape side you want to protect. – If “CHECK TAPE” is displayed, the protection tab has been broken. Put a piece of clear adhesive tape over the opening. Do not cover the Cr02 tape detection hole when covering the tab opening. CD Synchro Start Recording 1 Load a blank tape into tape deck 2 and a disc into a disc tray. 2 Press CD to select CD mode. • You can program the tracks in the order you want them to be recorded (see Programming Tracks). If you do not, the tracks are recorded according to the order on the selected disc. 3 Press REC to start recording. . The REC flag starts flashing. • CD will start playback automatically. 4 Press . to stop recording. Recording from other sources (only on tape deck 2) 1 Press TAPE ( TAPE 1•2 ) to select tape deck 2. 2 Load a blank tape into tape deck 2 with the open side downward. 3 Press SIDE on remote control to select the recording side. . The BACK or FRONT flag will be displayed, depending on the side selected. 4 Press A. REV to select the playback mode ( . or ¶ ). 5 Press DOLBY NR to record with Dolby NR (except in TAPE 1 mode). 6 Press CD, TUNER, TAPE 1 or AUX. • Start playback of the selected source. 7 Press REC to start recording. . The REC flag starts flashing. 8 Press . to stop recording. Notes: – Only . or ¶ mode is available during recording. – During recording, it is not possible to listen to another source. RECORDING English Dubbing tapes (from tape deck 1 to tape deck 2) 1 Press TAPE ( TAPE 1•2 ) to select tape deck 2. 2 Load the prerecorded tape into tape deck 1 and a blank tape into tape deck 2. . Make sure the tape in tape deck 1 has its full spool to the left. 3 (For Tape Deck 2 only) Press SIDE on the remote control to select the recording side. 4 Press DUB (HSD) oncefor normal speed dubbing or twice(within 2 seconds)for high speed dubbing. . “NORMAL” (normal speed) or “FAST” (high speed) will be displayed, followed by “DUBBING”. . The HSD flag appears on the display during high speed dubbing. • Dubbing will start immediately. . The REC flag starts flashing. 5 Press .to stop dubbing. Notes: – At the end of side A, flip the tapes to side B and repeat the procedure. – Dubbing of tapes is only possible from tape deck 1 to tape deck 2. – To ensure good dubbing, use tapes of the same length. – During high speed dubbing in Tape mode, the sound is reduced to a low volume. – You can listen to another source while dubbing. – Dolby NR button has no influence during dubbing (dubbing from tape deck 1 to tape deck 2). An original tape recorded with Dolby B NR automatically produces a copy with Dolby B NR. Recording the mixed sound / One Touch Recording • During microphone mixing, you can record the mixed sound on a tape in tape deck 2 except dubbing mode. • For One Touch Recording, as soon as you press REC, the current source (CD, TUNER or AUX) will be recorded on tape deck 2 1 Load a blank tape in tape deck 2. 2 Press REC to start recording. . The REC flag starts flashing. 3 Press .to stop recording. Note: – When you press RECORD while in TAPE mode, "SELECT SOURCE" will be displayed. One Touch Recording is not possible in TAPE mode. Digital Recording via Digital Out For CD digital recording, please refer to the Instructions Manual of the CD Recorder, digital audio equipment, etc. 23 English Viewing the Clock You can view the clock (if it is set) while the system is in standby mode or any source mode. I...

Download now

Please, enter two numbers from picture: