Press the clip of the red terminal and fully insert the stripped portion of the colored (or marked) speaker cable into the socket, then release the clip Speaker (left) DAB/FM T-type antenna AC power Speaker (right) b. Press the clip of the black terminal and fully insert the stripped portion of the black (or unmarked) speaker cable into the socket, then release the clip P001-P030_MCB275_05_Eng 12 2007.6.13, 10:28 English 13 Installation Connecting an additional appliance Connecting a USB device or memory card By connecting a USB mass storage device (including USB flash memory, USB flash players or memory cards) to the Hi-Fi system, you can enjoy the device’s stored music through the powerful speakers of Hi-Fi system. 1 Check you have unfolded the control panel. 2 Insert the USB device’s USB plug into the socket on the set ‘s foldable control panel. or for the devices with USB cable: a. Insert one plug of the USB cable (not supplied) to the socket on the set ‘s foldable control panel. b. Insert the other plug of the USB cable to the USB output terminal of the USB device. or for the memory card: a. Insert the memory card into a card reader (not supplied). b. Use a USB cable (not supplied) to connect the card reader to the socket on the set ‘s foldable control panel. 4 Select AUX mode on the set. Helpful hints: – Always refer to the owner’s manual of other equipment for complete connection. Connecting a non-USB device It is possible to use an additional appliance, e.g. TV, VCR or CD recorder with the set. On MCB275, you can playback music from an external source. 1 Follow Step 1 under Connecting a USB device. 2 Insert one plug of the audio cable (not supplied) to the socket AUX IN on the set ‘s foldable control panel. 3 Connect the other end of the audio cable to the AUDIO OUT terminal of the additional appliance. P001-P030_MCB275_05_Eng 13 2007.6.13, 10:28 Installation English Using AC power 1 Make sure all the connections have been made before switching on the power supply. 2 Connect the AC power adaptor to the wall socket.This switches on the power supply. When MCB275 is switched to standby, it is still consuming some power. To disconnect the system from the power supply completely, remove the power plug from the wall socket. The type plate is located on the rear of the set. For users in the U.K.: please follow the instructions on page 2. Warning! To avoid overheating of the system, a safety circuit has been built in. Therefore, your system may switch to Standby mode automatically under extreme conditions. If this happens, let the system cool down before reusing it (not available for all versions). 14 Preparation Before using the remote control 1 Pull out the plastic protective sheet. 2 Select the source you wish to control by pressing one of the source select keys on the remote control (for example DISC, FM). 3 Then select the desired function (for example EA , a , a). Remove the plastic protective sheet Replacing battery (lithium CR2025) into the remote control 1 Press the slot on the battery compar tment. 2 Pull out the battery compar tment. 3 Replace a new battery and fully inser t the batter y compar tment back to the original position. Setting the clock After connecting MCB275 to the power supply, set the clock first. 1 Press and hold STANDBY-ON/ ECO POWER to switch the set to Standby mode. . The display shows the set time. 2 In the standby mode, press and hold CLOCK on the remote control. . The hours digits star t flashing. 3 Press 4 / . (or . / ™ on the remote control) repeatedly to set the hours. 4 Press CLOCK to confirm. . The minute digits start flashing. 5 Press 4 / . (or . / ™ on the remote control) repeatedly to set the minutes. 6 Press CLOCK to confirm. – To exit without storing the clock setting press STOP 9. Helpful hints: – The clock setting will be erased when the system is disconnected from the power supply. – The set will exit from the clock setting mode if no button is pressed within 90 seconds. –To set the clock automatically by using a time signal which is broadcast together with the RDS signal see chapter RDS: Automatic clock setting via RDS. English 123CR2025 CAUTION! Batteries contain chemical substances, so they should be disposed of properly. 15 Basic Functions English Switching on/off the set and selecting functions 1 To switch on, press STANDBY-ON/ ECO POWER or SOURCE on the set (or y on the remote control). . The set switches to the last source selected. OR On the remote control, press the source button (e.g. DAB, FM, DISC, USB, AUX). 2 When the set is on, press STANDBY-ON/ ECO POWER to switch off (or y on the remote control). 3 To select your function, press SOURCE once or more on the set (or DAB, FM, DISC, USB, AUX on the remote control). Helpful hints: –You can also switch on the set by pressing CD OPEN • CLOSEc. Switching between Standby and ECO POWER mode 1 When the set is switched off, press and hold STANDBY-ON/ ECO POWER to switch between Standby and ECO POWER mode (or...