Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Connect the iPod/iPhone/iPad to the dock. Listen to the iPhone/iPod/ iPad 1 Press DOCK to select iPhone/iPod/iPad source. 2 Load your iPhone/iPod/iPad onto this product. 3 Select and play a file on your iPhone/iPod/ iPad. • To pause/resume the play, press . • To skip to a track, press / . • To stop the play, press . • To select a file by the remote control: press MENU to access the menu, press / to select an item, and then press OK to confirm. Note • The music stops when the iPhone receives an incoming call. EN 17 Charge the iPod/iPhone/iPad The docked iPod/iPhone/iPad begins to charge as soon as this product is connected to AC power. Note • iPod with color display, iPod classic, and iPod with video are not compatible with dock charging. Remove the iPod/iPhone/iPad 1 Pull the iPhone/iPod/iPad off the dock. 2 Hide the dock. 7 Listen to radio Note • Make sure that you have correctly connected and fully extended the antenna. • You can program a maximum of 30 DAB radio stations and 30 FM radio stations. • Check with local retailer or go to for the applicable DAB radio frequencies in your area. • Refer to “Product information” > “RDS program types” for more information about RDS radio stations. Store DAB radio stations automatically If no DAB radio station is stored, this product can search and store DAB radio stations automatically. 1 Press DAB/FM repeatedly to switch to the DAB mode. » [FULL SCAN] is displayed. 2 Press or OK to star t the auto installation. » This product automatically stores radio stations with sufficient signal strength. » After all available radio stations are stored, the first stored radio station is broadcast automatically. Basic operations Follow the instructions below for more functions. 18 EN Tune to the next FM radio station with sufficient signal strength at the lower/higher frequency: Press and hold / to star t the auto search. Tune to the FM radio station at a specific frequency: Press / repeatedly until the frequency digitals are displayed. Program FM radio stations automatically: Press and hold SCAN or PROGRAM to star t the auto programming. Program DAB radio stations automatically: Press and hold SCAN to star t the auto programming. Program radio stations manually: 1) Tune to a radio station. 2) Press PROGRAM to activate the programming. 3) Press / or / to assign a sequence number to the radio station. 4) Press PROGRAM to confirm. 5) Repeat steps 1-4 to program more radio stations. Tune to a preset radio station: Press / repeatedly. Switch the audio mode between [STEREO] (stereo) and [MONO] (monophonic) for FM radio: Press OK repeatedly. Display available information about the current radio station: Press RDS/INFO repeatedly. Synchronize the clock with an RDS radio station: 1) Tune to an RDS radio station that transmits time signals. 2) Press and hold RDS until [CT SYNC] is displayed. Use the menu When you listen to radio, you can access the menu for control options. 1 Press MENU or . » FM mode: [SCAN SETTINGS] is displayed. » DAB mode: [STATION] is displayed. 2 Press / or / to select a menu option, and then press OK or to confirm the option or enter the lower-level menu. FM mode [SCAN Search and store radio stations SETTINGS] automatically: [STRONG] for radio stations with strong signal only, [ALL] for all. [AUDIO] Select an sound mode: [STEREO] or [MONO]. [SYSTEM] [RESET]: Reset all settings to the factor y default status. [SW VER]: Display the current version of the firmware. [UPGRADE]: Upgrade the firmware. DAB mode [STATION] Access the list of the previously stored DAB radio stations. Press / or to select a station, and to star t listening. [FULL Scan and store DAB radio SCAN] stations within full range. [MANUAL] Tune to a DAB radio station manually. [DRC] Dynamic Range Control: Select a level for the effect of dynamic range control. [SYSTEM] [RESET]: Reset all settings to the factor y default status. [SW VER]: Display the version of the current firmware. [UPGRADE]: Upgrade the firmware. 3 Press MENU or to exit the menu. English EN 19 8 Other features Set the alarm timer You can use this product as an alarm clock.You can select CD, USB, Dock, iPod/iPhone/iPad playlist, FM, or DAB as the alarm source. 1 Make sure that you have set the clock correctly. 2 In the normal standby mode, press and hold TIMER until [TIMER SET] scrolls on the display. 3 Press VOL +/- to select an alarm source: CD, FM, DAB, USB, Dock, or iPod/iPhone/ iPad playlist. • To use iPod/iPhone/iPad playlist as the alarm source, create a playlist named “PHILIPS” in your iPod/iPhone/iPad first. • If no playlist named “PHILIPS” exists in the iPod/iPhone/iPad or the playlist includes no playable track, this product switches the alarm source to iPod/ iPhone/iPad. 4 Press TIMER to confirm. » The hour digits begin to blink. 5 Press VOL +/- repeatedly to set the hour, and then press TIMER to confirm. » The minute digits begin to blink. 6 Press VOL +/- to set the minute, and then press TIMER to confir...