Votes - 3, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
A stereo FM program cannot be received in stereo. • Press FM MODE until “MONO” disappears in the display. Tape deck The tape does not record or play, or there is a decrease in sound level. • The heads are dirty. Clean them (page 28). • The record/playback heads are magnetized. Demagnetize them (page 28). The tape does not erase completely. • The record/playback heads are magnetized. Demagnetize them (page 28). There is excessive wow or flutter, or the sound drops out. • The capstans in the tape deck are dirty. Clean them using a cleaning cassette (page 28). Noise increases or the high frequencies are erased. • The record/playback heads are magnetized. Demagnetize them (page 28). The tape does not record. • No cassette is loaded. Load a cassette. • The tab has been removed from the cassette. Cover the broken tab with adhesive tape (page 28). • The tape has wound to the end. 24GB Optional components There is no sound. • Refer to General item “There is no sound.” (page 23) and check the condition of the system. • Connect the component properly (page 22) while checking: – if the cords are connected properly. – if the cord plugs are firmly inserted all the way. • Turn on the connected component. • Refer to the operating instructions supplied with the connected component and start playing. • Press FUNCTION repeatedly until “MD” or “VIDEO” appears (page 22). The sound is distorted. • Set the volume of the connected component lower. If the system still does not operate properly after performing the above measures, reset the system as follows: Use buttons on the unit for the operation. 1 Disconnect the power cord. 2 Reconnect the power cord. 3 Press ?/1 to turn on the system. 4 Press x (CD stop), DSGX and ?/1 at the same time. The system is reset to the factory settings. You should set the settings you made, such as the preset stations, clock, and timer. Messages One of the following messages may appear or flash in the display during operation. CD/MP3 NO DISC There is no disc in the player. NO STEP All of the programed tracks have been erased. CD OVER You have reached the end of the disc while pressing and holding M during playback or pause. STEP FULL You tried to program 26 or more tracks (steps). PUSH STOP You pressed PLAY MODE during playback. Tuner COMPLETE The preset operation ended normally. Tape NO TAB You cannot record the tape because the tab has been removed from the cassette. Troubleshooting NO TAPE There is no tape in the tape deck. Timer SET TIMER You cannot select the timer function when Play Timer or Rec Timer are not set. TIME NG Play Timer or Rec Timer start and end times are set to the same time. PUSH SELECT You tried to set the clock or timer during timer operation. SET CLOCK You tried to select the timer with the clock not set. continued 25GB Other INVALID You pressed an invalid button. 26GB Additional Information Precautions On operating voltage • Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply. • The voltage selector is located at the bottom of the apparatus. On safety • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Unplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. To disconnect the power cord (mains lead), pull it out by the plug. Never pull the cord itself. • Should any solid object or liquid fall into the system, unplug the system and have it checked by qualified personnel before operating it any further. • AC power cord must be changed only at the qualified service shop. On placement • Do not place the system in an inclined position. • Do not place the system in locations where it is; – Extremely hot or cold – Dusty or dirty – Very humid – Subject to vibrations – Subject to direct sunlight. • Use caution when placing the unit or speakers on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result. On heat buildup • Although the system heats up during operation, this is not a malfunction. • Place the system in a location with adequate ventilation to prevent heat build-up in the system. • If you continuously use this system at a high volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet. • To prevent a malfunction, do not cover the ventilation hole. On operation • If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. Remove the disc and leave the system turned on for about an hour until the moisture evaporates. • When you move the system, take out any disc. If you have any questions or problems concerning your system, please consult your nearest S...
Other models in this manual:Home Stereos - CMT-GPX6 (362.59 kb)
Home Stereos - CMT-GPX7 (362.59 kb)