Votes - 5, Average rating: 4 ( )

Manafacture: Kenwood File size: 2.08 mb File name: Language of manual:

• If no stations have been stored in memory, “END” will appear for about 4 seconds. 25 EN • If 40 stations have already been stored in memory and the AUTO MEMORY button is pressed, “END” will appear immediately and the scan will be aborted. If you want to redo the ASPM operation from the beginning, erase the preset memory, and then perform steps 1 -4. • If the RDS station broadcast signals are very weak, station names may not be stored in memory. To stop the ASPM operation before it is complete : Press the AUTO MEMORY button whilst it is scanning for stations. • The stations that have already been stored in memory will be kept there. To erase all the contents in the preset memory : 1 Press the ON/STANDBY button to enter the standby mode. 2 Press the ON/STANDBY button whilst holding down the TUNER (BAND) button and the SOUND MODE button. • “PGM” will light up on the display and “TUNER CL” will appear. • After performing this operation, all of the preset memory in formation will be erased. 26 EN 1 2 3,5 3 4 5 4 1 2 3,5 3 4 5 4 To recall stations that have been stored in memory (PTY search) You can search for desired stations by specifying the programme type (see page 23 - 24) from among the stations that have been stored in memory. 1 Press the POWER button to turn the power on. 2 Press the TUNER (BAND) button to select the FM ST or FM band. 3 Press the PTY button. • “PTY TI” and “SELECT” will appear alternately for about 6 seconds. 4 Within 6 seconds, press the P. CALL (4 1 or . .) button to select the programme type you want. • Each time the button is pressed, the programme type will appear. If the button is held down for more than 0.5 second, the programme type will appear continuously. 5 Whilst the selected programme type is flashing (within 4 seconds), press the PTY button again. • After the name of the selected programme type has been lit for 2 seconds, “SEARCH” will appear, and the search operation will start. Notes : If the programme type has changed from flashing to steadily lit and the PTY button is pressed, nothing will happen. in this case, start again from step 3. Each time a station of the programme type you want is encountered, you will be able to listen to the broadcast. The channel number will flash for about 3 seconds.The station name will flash for 7 seconds, and then remain lit. • If you want to listen to another station of that programme type, press the PTY button whilst the channel number or station name is flashing. The unit will look for the next station of that type. • “NOT FOUND” will appear for 4 seconds, if the requested programme type station is not found. 27 EN If you have selected the traffic programme : If you select traffic programme (TP) as the programme type in step 4 (on page 27) , to receive only radio station which broadcast traffic programmes, the TP will appear. (However, this does not necessarily mean that you will hear any traffic announcements at that time.) When a traffic announcement is actually being made, the TA will appear. (When both the TP and TA will appear, an announcement is being made.) P.CALL 4 1 . . To manually recall the stations stored in memory Press the P. CALL (4 1 or . .) button. • Each time the button is pressed, the station name will change. • After the station name had been displayed, the channel number will appear for 2 seconds. The frequency for that channel will appear for another 2 seconds and finally the station name will be displayed. 28 EN RDS DISPLAY (RDS display) (No RDS station display) RDS DISPLAY (RDS display) (No RDS station display) To switch the display Each time the RDS DISPLAY button is pressed whilst an FM station is tuned in, the display will switch as follows: When the station you are tuning in is not an RDS station or even if it is an RDS station but it is very weak signal, the display will change in the following order : Notes : • “NO PS”, “NO PTY”, or “NO RT” will flash for about 5 seconds, and then the frequency will be displayed. • The display can only be switched whilst tuned to the FM band. Notes for Radio text • The radio text for 8 characters will be displayed steadily for 4 seconds and then it will scroll across the display. • If you tune into a station which is not broadcasting any radio text, even if it is an RDS station, when you switch to the radio text position “NO RT” will be displayed. • Whilst radio text data is being received or when the text contents change, “RT” will be displayed. Notes for RDS operation If any of the following events occur, it does not mean that the unit is faulty. • “PS”, “NO PS” and a station name appear alternately, and the unit does not operate properly. • If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly. • When you receive an RDS station whose signal is too weak, information like the station name may not be displayed, even if “RDS” is lit. 29 EN CASSETTE OPERATION 44 1 2,5 3 6 P.CALL 4 1 . . 2,5 6 ...

Download now

Please, enter two numbers from picture: