Votes - 2, Average rating: 5 ( )

Manafacture: Kenwood File size: 3.66 mb File name: Language of manual:

Unplug the power cord from the power outlet then, while holding the eject ENTER key depressed, plug the power cord again. ENTER Symptom Cause Remedy Remote control operation is not possible. OBatteries are exhausted. OThe remote control is too far away from the system, the controlling angle is deviated or there is an obstacle in between. OThere is no tape or CD set in the component to be played. OAn attempt is made to play the cassette deck which is recording something. OThe MULTI CONTROL setting mode is activated. OReplace with new batteries. OOperate the unit inside the remote controllable range. OSet a tape or CD in the component to be played. OWait until the recording ends. OCancel the MULTI CONTROL setting mode. ^ ^ & Receiver, speakers Symptom Cause Remedy Sound is not produced. OThe speaker cords are disconnected. OThe MUTE switch of remote control unit is switched ON. OThe headphone plug is inserted into the jack. OConnect properly referring to “System connection”. OSwitch MUTE OFF. OUnplug the headphone plug.* AUX (external input) sound is not produced. OThe AUX INPUT LEVEL control on the rear panel is set to MIN. OAdjust to an optimum level.u Sub-woofer sound is not produced. OThe LEVEL control is set to OFF. OAdjust to an optimum level.( Sound is not output in the TUNER mode. OEven when DEMO is ON, stations with weak radio waves are muted and their sound cannot be heard. OSwitch the demonstration off.4 The character display blinks and sound is not produced. OThe speaker cords are short-circuited. OTurn the power OFF, remove the short- circuit and turn the power ON again. Sound is not produced from the left or right speakers. OThe speaker cords are disconnected. OConnect properly referring to “System connection”. Sound is not produced from the surround speakers. ONo surround mode is activated. OSet a surround mode. The clock display shows “- - : - -”. OThere was a power failure. OThe power cord was unplugged from the outlet. OAdjust the present time again. OAdjust the present time again. YY Timer operation is not possible. OThe present time has not been adjusted or there was a power failure. OThe timer ON time and OFF time have not been set. OThe timer execution was not set up. OAdjust the present time referring to “Clock adjustment”. OSet the timer ON time and OFF time. OExecute the timer program. Y I P Radio stations cannot be received. OThe antennas have not been connected. OA proper broadcasting band has not been selected. OThe frequency of the station to be received is not tuned. OConnect antennas. OSelect a band. OTune to the frequency of the desired station. ¤ ¤ Noise interferes. OCar ignition noise. OInfluence of an electric appliance. OA TV set is installed near the system. OInstall the outdoor antenna in an apart position from the road. OSwitch the suspected electric appliance OFF. OInstall the TV or the system at an increased distance between them. Knowledge sections 63In case of difficulty 63In case of difficulty XD-951/A900/A700 (En) A station has been preset but it cannot be received by pressing the P.CALL key. OThe frequency of the preset station is not tunable. OThe preset memory has been cleared because the power cord has been unplugged for a long period. OPreset stations with tunable frequencies. OPreset stations again. ¦ ¦ Demonstration starts suddenly. OThe power plug was unplugged from the outlet while the power switch was ON, or there was a power failure. OThis is not malfunction. Press the MODE/ DEMO key to cancel the demontration. 4 General Symptom Cause Remedy No operation occurs when an operation key is pressed. OThe MULTI CONTROL setting mode is activated. OCancel the MULTI CONTROL setting mode. & Cassette deck Symptom Cause Remedy Sound cannot be produced by pressing the play key. OThe head is dirty. OThe tape is wound too tight due to irregular winding. OA nonrecorded tape is played. OClean the head referring to “Maintenance”. OTry another tape. OPlay a recorded tape. I No operation occurs even when an operation key is pressed. OThe cassette holder is not closed completely. OThe operation key is pressed immediately after closing the cassette holder. OThe operation key is pressed in less than 4 seconds after turning the power ON. OA tape is not inserted in the unit. OThe tape is wound too tight due to irregular winding. OThe tape is fully wound to one of the reels. OClose the holder completely. OPress operations keys in more than a few seconds after closing the holder. OPress operation keys after waiting for more than 4 seconds. OInsert a tape. OTry another tape. OChange the tape transport direction or reverse the tape insertion orientation. . . . The DPSS malfunctions. OThe tape used is not suitable for DPSS, for example the spaces between tunes may be too short. ORefer to “Searching for the desired music program (DPSS)”. ° In dubbing, the tape stops at different moments in decks A and B. OThis is due to the difference in the tape length or characteristics of the mecha...

Download now

Please, enter two numbers from picture: