Votes - 5, Average rating: 4 ( )

Manafacture: Aiwa File size: 322.34 kb File name: Language of manual:

Power supply OPE/BATT The OPE/BATT indicator lights up while the power is on. Using on AC house current Connect the AC cord as illustrated below. to the AC inlet of the unit supplied AC cord to an AC outlet (AC 120 V, 60 Hz) CAUTION Use only the supplied AC cord. Use with other cords may result in the risk of fire. Using on batteries Open the lid of the battery compartment on the rear and insert eight R14 (size C) batteries, not supplied, with the 0and 9marks correctly aligned. Then close the lid. To switch from AC power supply to battery power supply, disconnect the AC cord from the AC inlet. R14 (C) When to replace the batteries The OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation. Notes on batteries • Do not mix different types of batteries or old batteries with new ones. • When the unit is not to be used for a long period, remove the batteries to prevent needless battery wear. • Never recharge the batteries, apply heat to them or take them apart. • Remove dead batteries. If liquid leaks from the batteries, wipe thoroughly to remove. En ENGLISH 3 TAPE/ POWER/ 6STANDBY RADIO/BAND \A SKIP/SEARCH DOWN – TUNING – UP PLAY/PAUSE/ PRESET STOP/ MEMORY FM MODE/ OSC REPEAT/ SLEEP TAPE/ POWER/ 6STANDBY RADIO/BAND \A SKIP/SEARCH DOWN – TUNING – UP PLAY/PAUSE/ PRESET STOP/ MEMORY FM MODE/ OSC REPEAT/ SLEEP TUNER OPERATIONA 1 Press *RADIO/BAND repeatedly to select the desired band. FM AM The power is turned on and the previously tuned station is received. * or BAND on the remote control when the AC cord is connected (CSD-TD66 only) 2 Press r, t(TUNING DOWN, UP) to select a station. During FM stereo reception, is displayed. After listening, press TAPE/POWER/6STANDBY to turn the power off. For better reception FM Extend the rod antenna and orient it for the best reception. AM The antenna is inside the unit. Position the unit for the best reception. For quick tuning (Auto Search) Keep r, tpressed until the tuner starts searching for a station. When a station is tuned to, the search stops. If the broadcast signal is weak, it does not stop. To stop the search manually, press ror t. * FM MODE/OSC -If an FM stereo broadcast contains noise, press the button so that is displayed. Noise is reduced, although reception is monaural. To restore stereo reception, press the button again. -If a high-pitched sound is heard during AM recording, press the button repeatedly until the noise is reduced. Its position can be checked by “•” being on or off the display. * or MODE on the remote control (CSD-TD66 only) To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/ step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the interval as follows. 1 Press RADIO/BAND to display FM. 2 Press swhile pressing RADIO/BAND to display the AM frequency. When the AM tuning interval is changed, the preset stations are cleared. NOTE If the unit picks up noise from other electrical appliances nearby, like a TV or fluorescent lights, move the unit away. To listen with the headphones Connect headphones with a stereo mini plug to the \ jack on the rear of the unit. 4 ENGLISH 0-9, +10 MODE BAND cPLAY r, t sSTOP (CSD-TD66 only) PRESETTING STATIONS You can preset up to 15 stations in each band. 1 Select a station. 2 Press *sSTOP/MEMORY once so that “M” is displayed to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. Preset number Frequency * or son the remote control (CSD-TD66 only) 3 Repeat steps 1 and 2. The next station will not be stored if a total of 15 preset stations have already been stored for a band. To listen to preset stations Select a band then press ePLAY/PAUSE/PRESET repeatedly. cPLAY on the remote control is also available (CSDTD66 only). To select a preset number directly with the remote control (CSD-TD66 only) Press the numbered buttons 0-9 and +10. Example: To select number 15, press +10 and 5. To select number 10, press +10 and 0. To clear a preset station Select the preset number first. Within 4 seconds, keep spressed until “M” and the preset number disappear in the display. The higher numbers in the band are decreased by one. Remote Control (CSD-TD66 only) Insert two R6 (size AA) batteries. R6 (AA) When the reach of the remote control signal is less than 5 meters (16 feet), replace the batteries. The remote control may not operate correctly when: -The unit is exposed to intense light, such as direct sunlight -Objects block the remote control signal to the unit To use the buttons on the remote control Buttons on the remote control and the main unit with identical indications have the same functions. To turn the power on Press POWER to turn on the display. When using the unit on the batteries, this button will not turn the power on. To turn the power off Press POWER to turn off the display. When one of the deck operation buttons is pressed...

Download now

Please, enter two numbers from picture: