Votes - , Average rating:
(
)
)
Manafacture: Goldmund
File size: 239.07 kb
File name: 94eeb13c-daa1-4712-8815-8db1ce5bb52f.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
CHOICE OF YOUR TURNTABLE LOCATION 4 3. TURNTABLE ASSEMBLY 5 4. TONE ARM ASSEMBLY 19 5. USER INSTRUCTIONS 20 6. CLEANING AND MAINTENANCE 21 I M P O R T A N T ! The Goldmund Reference II you just purchased represents a summit in terms of design, concept and quality of reproduction. Therefore, great care should be taken before attempting to put the unit together. Read the instruction manual carefully. This will eliminate the risk of damage or loss in performance. WARNING! PLEASE READ INSTALLATION MANUAL COMPLETELY PRIOR TO INSTALLATION. PLEASE DO NOT CONNECT ANY CABLES OR MOVE ANY PART BEFORE READING THE FOLLOWING INSTRUCTIONS. OBSERVE GENERAL ELECTRICAL SAFETY PRECAUTIONS PARTICULARY WITH REGARD TO AVOIDING WATER, MOISTURE AND HEAT. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVERS AND REFER SERVICING TO QUALIFIED PERSONNEL. The Goldmund manual 1 UNPACKING WARNING! PLEASE READ INSTALLATION MANUAL COMPLETELY PRIOR TO INSTALLATION. 3 PERSONS ARE NECESSARY TO INSTALL THIS TURNTABLE Your turntable is shipped in 4 separate wood boxes labeled 1 to 4 and 1 carton box labeled 5: - Box 1: the base (feet assembly) - Box 2: the table top - Box 3: the tripod - Box 4: all mechanical parts to be assembled - Box 5:the power supply The electronic control box is already assembled under the table top. ATTENTION Please keep the packaging in case you need to transport the turntable at a later date or if you have to send it for maintenance. This packaging has been designed specifically to protect the Reference turntable in transit. Use of alternative packaging is likely to result in damage, 2 CHOICE OF YOUR TURNTABLE Due to the total weight of your turntable (300kg), please choose the definitive location of your turntable in order to install it on site. Locate the player on a support providing possible connection to the floor. Solid coupling is essential, and if your support is standing on a suspended one foot should be located over close to a supporting wall for an optimal result. The Goldmund manual 3 TURNTABLE ASSEMBLY BACK FRONT STEP 1 Box 1: the base (feet assembly) Unscrew and remove the top of the wood box n°1. Remove the protection cover. Unscrew and remove a side of the wood box. Free the feet base and position it at its definitive location, the red bar on the back. Note: Make sure the small screen is facing toward the front, with both central pointes bolt on the back. STEP 2 Box 2: the Table top Unscrew and remove the top cover of the wood Remove the protection cover, Mount the table top on the base with the Then, unscrew the cover hiding of the Free the control panel cables from all cables through base. The Goldmund manual STEP 3 Box 3: Tripod Unscrew and remove the top cover of the wood box n°3. Remove the protection cover. Remove the 3 cylindrical weights sitting on top of the tripod feet. STEP 4 Box 3: Tripod Unscrew the tripod from its 3 feet. Keep the 3 screws that you will use The Goldmund manual STEP 5 Box 3: Tripod Free the tripod assembly from the box and set it on 3 temporary supports like foam rubber or books, leaving the center free. The Goldmund manual STEP 6 Box 3: Tripod In the box n°3, you will find the 3 cylinder feet of the tripod. Please take one cylinder foot to position it at the front left position. Be carful to select the foot with the correct basis (check the bottom . Repeat the operation for the front right cylinder foot. The Goldmund manual Box 4: Various Parts In the box n°4, you will find: - 1 platter - 1 motor bloc - 1 belt - 12 rubber seals - 1 large golden insert - 3 small golden insert - 1 clamp - 1 small oil bottle STEP 7 Box 4: Various Parts Take the large golden insert. STEP 8 Position it in the center of the The Goldmund manual STEP 9 Box 3: the tripod In the box n°3, take the last cylinder foot. Check if its design is the same as the one shown on the left picture. Position it in the bottom of the third cylinder foot position, passing the axe through the hole. The 3 cylinder feet are positioned. The Goldmund manual 10 STEP 10 Adjust the 3 springs: Turn the springs has shown. Too High Too low Correct position The Goldmund manual 11 STEP 11 Take 4 rubber seals and insert them in one of the 3 holes on the table: 4 rubber seals per hole. Repeat the operation for both other holes. STEP 12 When the seals are positioned, place 1 golden Repeat the operation for both other The Goldmund manual 12 STEP 13 For this step, you need to be 2 persons. One person take carefully the motor block by its basis and keep in above the 3 holes with the golden insert, as shown on the picture. The other person runs the cables trough the central hole and leave them hanging Then the first person can mount the motor on the table, making each black serrated knurl facing its golden insert. ATTENTION: Please check the motor and the motor black knurl is in the same position one shown on the picture. The Goldmund manual 13 BACK FRONT BACK FRONT STEP 14 Take the tripod and mount it as shown on the left pict...