Votes - 1, Average rating: 5
(
)
)
|
manual abstract
-Increase the separation between the equipment and receiver. -Connect the equipment into an circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio TV technician for help. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance. RISK OF ELECTRIC SHOCK CAUTION The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION For Compact Disc Units Only: INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM. General Troubleshooting TURNTABLE The Unit does not operate. 1 The AC Power Cord is not well connected. 2 The ON/OFF VOLUME KNOB (11) is not turned on. There is no sound. 1 The white protective needle cover was notremoved. 2 The volume has not been turned up. Specification Power Supply : AC 120V 60Hz Power Consumption : 15W Speed : 33 /45 /78 RPM Speaker : 3X5” DYNAMIC TYPE x2 * DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. 6 Turntable Operation 1 Turn the unit on by switching the ON/OFF VOLUME KNOB (11) to the ON position. The POWER LIGHT INDICATOR (6) will come on. 2 Use the CUE LEVER (5) to raise the tone arm. Move the TONE ARM (12) by hand over therecord and slowly lower it using the CUE LEVER(5). Adjust the volume to the desired level byturning the ON/OFF VOLUME KNOB (11). 3 At the end of the record, the tone arm will automatically return to its rest. The red powerlight will remain on until the unit is turned off. Use the Tone control to adjust the sound quality. Tone Control Turntable Operation 1 Turn the unit on by switching the ON/OFF VOLUME KNOB (11) to the ON position. The POWER LIGHT INDICATOR (6) will come on. 2 Use the CUE LEVER (5) to raise the tone arm. Move the TONE ARM (12) by hand over therecord and slowly lower it using the CUE LEVER(5). Adjust the volume to the desired level byturning the ON/OFF VOLUME KNOB (11). 3 At the end of the record, the tone arm will automatically return to its rest. The red powerlight will remain on until the unit is turned off. Use the Tone control to adjust the sound quality. Tone Control Welcome Table of Contents Turntable Operation Getting Started Control Locators........................... Unpacking.................................... Power Source.............................. 4 5 5 Turntable Operation Turntable Operation..................... Tone Control ................................ Accessory: Adapter for 45 rpm ...................................................... 6 6 6 General Troubleshooting Guide................ 7 Warranty....................................... 8 Accessory: ADAPTER FOR 45 RPM To play the 45 rpm record, place the adapter on the center of the turntable. This unit includes ONE (1) adapter found in the polybag of the instruction manual. Thank you for purchasing the Empire Turntable(CR46). Before operating this unit, please read thismanual thoroughly and retain it for future reference. About This Manual Instructions in this manual describe the control functions of the CR46. Control Locators Getting Started & Basic Operation Control Locators Getting Started & Basic Operation Unit Controls 13 1. ADAPTER FOR 45 RPM RECORDS 2. TURNTABLE 3. SPINDLE 4. TURNTABLE SUSPENSION SCREW 5. CUE LEVER 6. POWER LIGHT INDICATOR 7. TONE ARM REST 8. HOLD DOWN CLIP 9. SPEED CONTROL SWITCH 10. TONE CONTROL 11. ON/OFF VOLUME KNOB 12. TONE ARM 13. SPEAKER 14. AC POWER PLUG Unpacking 12 2 3 4 5 6 7 9 10 11 8 1 1 Remove packing materials from unit. Note: Save all packing materials. 2 Remove plastic safety cover from A/C plug. 3 Remove tie from A/C cord 4 Open lid and remove styrofoam shippingmaterial from turntable. 5 Remove black tie-wrap from under the tone arm. 6 Remove white protective needle cover by gentlypulling towards the front of the unit. 13 7 Using your fingers, turn the turntable suspensionscrew (4) clockwise until it is all the way down. Do not force it. This allows turntable to float on its shock absorbers. 14 Power Source 1 Unwind the AC POWER CORD (11) at the backof the unit and connect it to a power outlet. 2 Plug A/C cord into appropriate outlet. AC Polarized Plug Note: This product may be equipped with apolaized alternating-current line plug (aplug having one blade wider than theother.) This pl...