Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Sharp edged or hard articles are prohibited. The gathering of dew in the panel may occur with abrupt temperature or humidity changes. A stable environment condition is recommended. Keep the surface clean. No adhesives should be applied. Avoid high voltage and static charge. Wall mounting You can mount the panel to the wall instead of to the foot, by means of the supplied mounting plate. If you do not need to mount the panel to the wall, please skip this item. Step 1: Remove the panel from the foot 1. Position one hand under the panel at the front side. Position the other hand at the rear, under the push-button with BARCO logo (9). Installation 15 2. Firmly press down the push-button (9) with one hand while carefully lifting the panel up with the other hand. 3. Remove the panel from the foot. Step 2: Fix the mounting plate to the wall 1. Screw the mounting plate to the wall with the 4 supplied screws (A). 2. Slide back the locks at both sides of the mounting plate (B). In that way, you can secure the panel to the mounting plate after placing the panel. Step 3: Place the panel on the mounting plate 1. Place the panel on the mounting plate (C). If you want to secure the panel to the mounting plate, place the panel in the frontmost notches. A B Installation 16 Please make sure that the four shafts are securely placed in the notches of the mounting plate. 2. To secure the panel, slide forward the locks on both sides of the mounting plate. Lock the panel with one screw at both sides (D). Connecting the signals C D 1 2 3 Installation To connect the video & sync signals: 1. Connect one end of the appropriate video cable to the corresponding video input of the monitor. • Analog video: Connect to input (3) • DVI: Connect to input (2) 2. Connect the other end of the video cable to the video output of your video source. • Analog video: Computer graphics board with analog video output • DVI: Computer graphics board with digital video output To connect the power: 1. Connect one end of the proper power cable to the AC input of the 12V DC adapter. 2. Connect the 12V supply of the 12V DC adapter to the DC input (1) of the monitor. 3. Connect the other end of the power cord to a grounded power outlet. Starting up Proceed as follows: 1. Switch on the computer. 2. Switch on the display by pushing the Power key (1). 3. If necessary, select a suitable resolution in the computer operating system. Please refer to Appendix A, "Possible resolutions" in the back of this manual. Installation 1 Note: The recommended resolution for best image quality is 1280x1024 at 60 Hz. The microcontroller in the display checks if the connected video signal has been adjusted before, and if these adjustments have been stored in the memory. There are 2 possibilities: a) The video signal has been adjusted and stored in the memory. In this case, the display switches to this memory location (the so- called mode) and the image will need no further adjustments. b) The video signal has not been adjusted and stored yet. In this case, the display will auto-size the picture and store the settings in one of the user modes. Note: For analog video signals we advise to perform an Auto Color action in this case. Install the software NioWatch software: Insert the CD-ROM in the CD-ROM drive. The CD-ROM starts automatically. Please follow the instructions on the screen. The CD-ROM contains user instructions about the usage of the NioWatch. Installation Touch panel software: Please refer to the TouchKit installation & user manual on CD-ROM. On-screen display (OSD) On-screen display (OSD) How to use the OSD 12 3 4 The OSD is a window on your screen that allows you to view and change display settings. To change an OSD setting, proceed as follows: 1. Press the Menu key (3) on the front to display the OSD main menu. Note: It may be possible that the OSD menu does not appear. If this is the case, the front Controls are locked. To unlock them, please follow the procedure described in § 3.2 below. 2. There are 5 OSD submenus divided by categories. Press the < (left) key (1) or > (right) key (2) to scroll to the desired menu item. 3. Press the Menu key (3) to activate the selected function or to enter the selected submenu. 4. If you have activated a function: On-screen display (OSD) a) Press the < (left) key (1) or > (right) key (2) to change the value. b) Press the Menu key (3) to enter the new value and return to the menu. 5. The current settings are saved automatically when you return to the previous level or exit the OSD menu. 6. The Auto key (4) acts as Exit function while the OSD is on the screen. Pressing the Auto key (4) takes you back to the previous level in the OSD. Pressing the Auto key (4) while the main menu is on the screen closes the OSD. 7. The OSD disappears automatically after an inactivity period of 60 seconds (default setting). The current settings will be saved. Description of the menu items Brightness / Contrast menu BRIGHTNESS > CONTRAST > BRIGHTNESS/CON...
Other models in this manual:Displays - MFCD 1219 (504.85 kb)