Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
* This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode set to On. Transmission [d][e][ ][Set ID][ ][Data][Cr] Data 00 to 32: -50 (Left) to 0 (Right) *Left/Right values depend on Tile H size. ** It may not be supported depending on the model. Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x] 43. Tile V Position (Command: d f) To adjust the Tile Vertical position. * This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode set to On. Transmission [d][f][ ][Set ID][ ][Data][Cr] Data 0 to 32: 0 (Bottom) to 50 (Top) * Bottom/Top values depend on Tile Vertical size. ** It may not be supported depending on the model. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x] 44. Tile H Size (Command: d g) To adjust the Tile Horizontal Size. *Set Tile H Position to 0x32 before setting Tile H Size. * This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode set to On. Transmission [d][g][ ][Set ID][ ][Data][Cr] Data 00 to 32: 0 to 50 ** It may not be supported depending on the model. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x] 45. Tile V Size (Command: d h) To adjust the Tile Vertical size. *Set Tile V Position to 0x00 before setting Tile V Size. * This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode set to On. Transmission [d][h][ ][Set ID][ ][Data][Cr] Data 00 to 32: 0 to 50 ** It may not be supported depending on the model. Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x] 46. Natural Mode (In Tile Mode) (Command : d j) To display the image naturally, the part of the image that would normally be displayed in the gap between the monitors is omitted. Transmission [d][j][ ][Set ID][ ][Data][Cr] Data 00: Off 01: On Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x] 47. DPM Select (Command: f j) To set the DPM (Display Power Management) function. Transmission [f][j][ ][Set ID][ ][Data][Cr] Data 00: Off 01: On * Data settings may vary depending on your model as below. Data 00: Off 01: 5 sec. 02: 10 sec. 03: 15 sec. 04: 1 min. 05: 3 min. 06: 5 min. 07: 10 min. Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x] 48. FAN Control (Command : d o) To set the Fan mode. Transmission [d][o][ ][Set ID][ ][Data][Cr] Data 00: Auto 01: On 02: Manual 03: Off ** It may not be supported depending on the model. Acknowledgement [o][ ][Set ID][ ][OK/NG][Data][x] 49. FAN Fault Check (Command: d w) To check the fan errors. Transmission [d][w][ ][Set ID][ ][Data][Cr] Data FF: Read the status Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x] Data 00: Fan fault 01: Fan OK 02: Model without a Fan 50. Temperature Value (Command: d n) To check the inside temperature value. Transmission [d][n][ ][Set ID][ ][Data][Cr] Data FF: Check the status Acknowledgement [n][ ][Set ID][ ][OK/NG][Data][x] [n][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x] * Temperature is displayed in he...