Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
EN-3 POWER SAVING The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. State LED Light ON Blue Power Saving Mode Amber The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 3 seconds. DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC2B standard. EN-4 CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 24-Pin Color Display Signal Cable* PIN Meaning PIN Meaning 1. TMDS Data213. NC 2. TMDS Data2+ 14. +5V Power 3. TMDS Data 2/4 Shield 15. Logic Ground 4. NC 16. Hot Plug Detect 5. NC 17. TMDS Data06. DDC Clock 18. TMDS Data0+ 7. DDC Data 19. TMDS Data 0/5 Shield 8. NC 20. NC 9. TMDS Data121. NC 10. TMDS Data1+ 22. TMDS Clock Shield 11. TMDS Data 1/3 Shield 23. TMDS Clock+ 12. NC 24. DDC TMDS Clock EN-5 19-Pin Color Display Signal Cable* PIN Meaning PIN Meaning 1. TMDS Data2+ 10. TMDS Clock+ 2. TMDS Data2 Shield 11. TMDS Clock Shield 3. TMDS Data212. TMDS Clock4. TMDS Data1+ 13. CEC 5. TMDS Data1 Shield 14. Reserved (N.C. on device) 6. TMDS Data115. SCL 7. TMDS Data0+ 16. SDA 8. TMDS Data0 Shield 17. DDC/CEC Ground 9. TMDS Data018. +5V Power 19. Hot Plug Detect * only for certain models *19-Pin Color Display Signal Cable PIN NO. DESCRIPTION 7. MHL+ 9. MHL- 18. VBUS 19. CBUS 5, 11, 17 GND *Only for MHL models EN-6 STANDARD TIMING TABLE Mode Resolution 1 640x480 60 Hz 2 MAC 640x480 66.66 Hz 3 VESA 720x400 70 Hz 4 SVGA 800x600 56 Hz 5 SVGA 800x600 60 Hz 6 XGA 1024x768 60 Hz 7 XGA 1024x768 70 Hz 8 VESA 1152x864 75 Hz 9 SXGA 1280x1024 60 Hz 10 VESA 1280x720 60 Hz 11 WXGA 1280x800 60 Hz 12 WXGA+ 1440x900 60 Hz 13 WSXGA+ 1680x1050 60 Hz 14 UXGA 1920x1080 60 Hz *Only for MHL-Model Mode Resolution 1 640x480 @60Hz 2 720x480p @60Hz 3 720x576p @50Hz 4 800x600 @60Hz 5 1024x768 @60Hz 6 1280x720p @60Hz 7 1280x720p @50Hz 8 1920x1080p @30Hz EN-7 EN-8 INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. 1-1 Connect Video Cable a. Make sure both the monitor and computer are powered-OFF. b. Connect the VGA video cable to the computer. 1-2 1-4 2. Connect the adapter a Connect the AC cord to the adapter. b Connect one end of the adapter to the monitor and the other end to a p roperly g rounded, AC outlet . 3. Power-ON Monitor and Computer Power-ON...