Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
Mode LED light On Blue Power saving Amber The power saving mode will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from "power saving" mode back to "on" is around 3 seconds. Display Data Channel (DDC) To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing. The monitor supports the DDC2B standard. EN-4 Connector pin assignment 156101115 15-pin color display signal cable PIN No. Description PIN No. Description 1 Red 9 +5 V 2 Green 10 Logic ground 3 Blue 11 Monitor ground 4 Monitor ground 12 DDC-serial data 5 DDC-return 13 H-sync 6 R-ground 14 V-sync 7 G-ground 15 DDC-serial clock 8 B-ground EN-5 24-pin color display signal cable* PIN No. Description PIN No. Description TMDS data 213 NC TMDS data 2+ 14 +5 V power TMDS data 2/4 shield 15 GND (return for +5 V hsync.vsync) NC 16 Hot-plug detection NC 17 TMDS data 0DDC clock 18 TMDS data 0+ DDC data 19 TMDS data 0/5 shield NC 20 NC TMDS data 121 NC TMDS data 1+ 22 TMDS clock shield TMDS data 1/3 shield 23 TMDS clock+ NC 24 DDC TMDS clock * only for certain models EN-6 Standard timing table VGA 640.480 60 Hz MAC 640.480 66.66 Hz VESA 720.400 70 Hz SVGA 800.600 56 Hz SVGA 800.600 60 Hz XGA 1024.768 60 Hz XGA 1024.768 70 Hz VESA 1152.864 75 Hz VESA 1280.720 60 Hz WXGA 1280.800 60 Hz WXGA+ 1600.900 60 Hz EN-7 Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cable a Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable (only for dual-input models). (1) Make sure both the monitor and computer are switched off. (2) Connect one end of the 24-pin DVI cable to the back of the monitor and the other end to the computer's port. 2 Connect the power cord Connect the power cord to the monitor, then to a properly grounded AC outlet. 3 Turn on the monitor and computer Turn on the monitor first, then the computer. This sequence is very important. If the monitor does not function properly, please refer to the troubleshooting section to diagnose the problem. 5 Optional:Connect the audio input socket(AUDIO IN) of the LCD monitor and the line-out port on the computer with the audio cable. 4 EN-8 USER CONTROLS Power Switch / Power LED: To turn the monitor ON or OFF. Lights up to indicate the power is turned ON. Using the Shortcut Menu Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly accessed settings. Empowering: Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes. AUTO Auto Adjust: Press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. MENU OSD functions Press this botton to activate the OSD menu. INPUT Input Key Use Input key to select from different video sources that may be connected to your monitor. (a) VGA input (b) DVI input As you cycle through the sources you will see the following messages on right top side of screen to indicate currently selected input source. It may take 1 or 2 seconds for the image to appear. VGA or DVI If either VGA or DVI input is selected ,but the VGA and DVI cables are not connected, a floating dialog box indicates: “No Cable Connect” or “No Signal” EN-9 Acer e Col or Ma nag em ent O p eratio n in s tr u cti o ns Step 1: Press “ “ Key to open the Acer eColor Management OSD and access the scenario modes Step 2: Press “ “ or “ ” to select the mode Step 3: Press “ AUTO “ Key to confirm the mode and exit the eColor menu. F eatures and Benefits Ma in Menu icon Sub Menu icon Sub Menu item D e scrip tion N/A User mode User defined. Settings can be fine-tuned to suit any situation N/A ECO mode Adjusts the settings to reduce power consumption. N/A Standard mode D efa u lt Set ti ng . R e fl ec t s na ti v e d is p lay capability N/A Grahpic mode Enhances colors and emphasize fine detail. Pictures and photographs appear in vibrant colors with sharp detail. N/A Movie mode D isplays scenes in clearest detail. Presents g r e a t v is u a l s , e v e n i n un s u it a b l y-l it environments. EN-10 Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following page: Adjusting the picture quality 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Picture from the OSD. Then navigate to 3 4 the picture element you wish to adjust. U...