MONITOR SIGNAGE MODELS 26TS30MF 47TS30MF 2 CONTENTS ENG ENGLISH CONTENTS 3 INSTALLATION PREPARATION 3 Accessories 4 Mounting Holes 6 Unpacking and Cabling 8 Portrait Layout (Only supported for 47TS30MF) 9 Storage Method for Panel Protection 9 - Correct Method 9 - Incorrect Method 10 PRODUCT INSTALLATION 10 Lighting installation 11 Installation in Enclosure 12 Precaution 12 - Correct Method 12 - Incorrect Method 13 TROUBLESHOOTING 14 SPECIFICATIONS 14 26TS30MF 15 47TS30MF 16 LVDS PIN MAP GUIDE 16 26TS30MF 17 47TS30MF INSTALLATION PREPARATION 3 ENG ENGLISH INSTALLATION PREPARATION Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. CD (Owner's Manual)/ Card/ Easy Setup Guide CAUTION yyDo not use any unapproved or counterfeit parts or accessories to ensure the safety and product life span. yyAny damages or injuries by using unapproved items are not covered by the warranty. NOTE yyThe accessories supplied with your product may vary depending on the model. yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions. INSTALLATION PREPARATION 4 ENG ENGLISH Mounting Holes 26TS30MF Use M3 x 4 mm screws to mount the monitor. There are 16 screw holes on the rear side of the product. < Front side of the product > < Rear side of the product > 47TS30MF Use M3 x 4 mm screws to mount the monitor. There are 20 screw holes on the rear side of the product. < Front side of the product > < Rear side of the product > CAUTION yyThis product has the front and back sides. Make sure the product is installed with the front side facing forward. yyImage is displayed reversely on the back side. Unpacking and Cabling 26TS30MF 2 Remove the top packaging. 1 Lift up the cover of the box. 4 Remove the poly bag. 3 Hold both sides of the product and lift it up. 6 Connect the LVDS cable(Additional assembly is required). A scaler board or LVDS cable is optional and not provided with the product. 5 Place a soft cloth on the table and put the product down with the screen facing downward. 47TS30MF 2 Remove the top packaging. 1 Lift up the cover of the box. 4 Remove the poly bag. 3 Hold both sides of the product and lift it up. 6 Connect the LVDS cable(Additional assembly is required). A scaler board or LVDS cable is optional and not provided with the product. 5 Place a soft cloth on the table and put the product down with the screen facing downward. NOTE yyPlease refer to "LVDS Pin Map Guide" on pages 16 to 18 for the LVDS cable assembly. Portrait Layout (Only supported for 47TS30MF) To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front. The portrait mode is only available on the scaler board.(The scaler board should support portrait mode.) CAUTION yyThe 26TS30MF model cannot be rotated. yyThe scaler board is optional and it is not part of the product. Storage Method for Panel Protection Correct Method Incorrect Method Panel Cushion Panel When laying down the product, place a cushion or a soft cloth on a flat floor. Put the product down with the panel of the product facing down. If the product is tilted onto the bezel, the bottom of the panel may be damaged. Panel Panel If there is no a cushion or a soft cloth available, ensure the floor is clean. Then lay the product down carefully with the panel facing either upward or downward. At this time, make sure that no object falls on the panel. If the product is tilted onto the edge of the panel, the panel may be damaged. 10 PRODUCT INSTALLATION ENG ENGLISH PRODUCT INSTALLATION Lighting installation This product must be installed with lighting. Lighting must be installed behind the product so that the display can be seen clearly. Lighting 600 lux or more Installing a certain object behind the screen may require additional lighting. Additional lighting Object Lighting 600 lux or more Additional lighting 11 PRODUCT INSTALLATION ENG ENGLISH Installation in Enclosure Install the product in the enclosure. 1 Place the product in the enclosure. 2 Attach the product using the prepared screw holes and an additional enclosure guide frame. < Example of the product in the enclosure > NOTE yyThis product can be installed in various locations besides the enclosure. < Example of the lighting installation > Lighting must be installed in the enclosure. CAUTION yyThe panel of this product is so thin that it can be easily broken when it is exposed to the outside. Please use the protective glass to prevent the product from directly being exposed to the outside. Precaution Incorrect Method Correct Method Do not lift up the product by holding a corner. Do not hold the screen area when holding the product. CAUTION yyMake sure the power is disconnected before moving or installing the product.Otherwise electric shock may occur....

Other models in this manual:
Displays - 47TS30MF-B (998.46 kb)