Votes - 0, Average rating: 0 ( )

Manafacture: LG File size: 2.36 mb File name: Language of manual:

IPS LED MONITOR MODEL 27EB22PY Accessories Accessories Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer. User's Guide/CardsPower Cord15-pin D-Sub Signal Cable(To set it up, this signal cable may beattached to this product beforeshipping out.) DVI-D Signal Cable(This feature is not available in allcountries.) NOTEThis accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores (core in the connector) to maintain standard compliance for the product. Audio CableUSB CableCable Holder 1 Connecting the Display Connecting the Display Connecting the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2.Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. WARNING The tape and locking pin may only be removed from those monitors equipped with astanding base when the base is pulled up. Otherwise, you may be injured by the protrudingsections of the stand. Product Handling with Care:When you lift up or move the product, Do Not hold or touch thefront part of LCD panel. It will damage the panel. (Please hold the Stand Body or plastic cover ofthe product.) stand Basestand Body 2 Connecting the Display Connecting the DisplayUse a coin on the back of the stand base and turn the screw clockwise to tighten. stand Base 4.Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2.When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. IMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the itemsshown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and getdamaged or injure your foot. stand Basestand Body 3 Connecting the Display Connecting the Display After installation, adjust the angle as shown below. 1.Adjust the position of the panel in various ways for maximum comfort. Tilt Range Swivel Range : 355° Height Range : maximum 5.12 inches (130.0 mm) 130.0mm * Please be sure toremove the Locking pin to adjust the height. 4 Connecting the Display Connecting the Display When adjusting the angle of the screen, do not put your finger(s) inbetween the head of the monitor and the stand body. You can hurt yourfinger(s). When adjusting the height of the screen, do not put your finger(s) inbetween the head of the monitor and the stand base. You can hurt yourfinger(s). ERGONOMICIt is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tiltangle of the monitor should not exceed 5 degrees. WARNINGYou do not need to replace the Locking pin after it is removed, to adjust its height. 5 Connecting the Display Connecting the Display -The pivot function allows you to rotate the screen 90 degrees clockwise. 1.Lift the monitor to its highest height to utilize the Pivot function. 2.Landscape & Portrait : You can rotate the panel 90o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If themonitor head touches the Stand Base, then the Stand Base could crack. Stand sectionHead section 3.Be careful with the cables when rotating the screen. 6 Connecting the Display Connecting the Display 1.Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. ABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. 12NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. CConnect Audio CableDConnect DisplayPort Cable (Separate purchase) Wall-outlet typeMac adapter :For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin 2row connector. When using a D-Sub signal input cableconnector for Macintosh Varies according to model. DVI-D (This feature is not available in all countries.) Connect the signalinput cable and tightenit up by turning in thedirection of the arrowas shown in the figure. WarningPlease pull the DVI cable first,then pull DisplayPort cable, for protect your finger. 7 Connecting the Display Connecting the DisplayPut the power cord and cables into the cable holder. 4.Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function'is executed automatically. (Only Analog Mode) Power Button NOTE‘ Self...

Download now

Please, enter two numbers from picture: