Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
Avoid touching the screen at all times, as this may result in damage to the screen or some of the pixels used to create images. CAUTION yyIt is recommended to move the TV in the box or packing material that the TV originally came in. yyBefore moving or lifting the TV, disconnect the power cord and all cables. yyHold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area. yyWhen holding the TV, the screen should face away from you to prevent the screen from scratches. yyWhen transporting the TV, do not expose the TV to jolts or excessive vibration. yyWhen transporting the TV, keep the TV upright, never turn the TV on its side, or tilt towards the left or right. 3 Attach the Stand Base from the Stand Body by turning the screw to the right with a Coin. Setting up the TV 19MA31D M1931D Attaching the Stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. 1 Place the TV with the screen side down on a flat and cushioned surface. CAUTION CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen attaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. Tighten the screws firmly to prevent the TV from tilting forward. Do not over tighten. 2 Attach the Stand Body from the TV. 3 Secure the TV and the Stand Body with the 2 screws. M2631D If you are not mounting the TV to a wall, use the following instructions to attach the stand. 1 Place the TV with the screen side down on a flat and cushioned surface. WARNING If you don`t fasten the screw tightly, TV will fall down and get damaged. 4 Attach the Stand Base from the Stand Body by turning the screw to the right with a Coin. 2 Attach the Stand Body from the TV. Insert the two Lockers of the Stand Body right into the groove of the TV head and secure them by pressing the left and right bottom sides. Locker CAUTION Tighten the screws firmly to prevent the TV from tilting forward. Do not over tighten. Mounting on a table 1 Lift and tilt the TV into its upright position on a table. Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. 10 cm 10 cm 10 cm 10 cm or WARNING When you adjust the angle, do not hold the buttom of the TV frame as shown on the following illustration, as may injure your fingers. CAUTION CAUTION Disconnect the power cord first, and then move or install the TV. Otherwise electric shock may occur. Do not place the TV near or on sources of heat, as this may result in fire or other damage. Using the Kensington security system NOTE Tilt from +20 to -5 degrees up or down to adjust the angle of the TV to suit your view. The Kensington security system connector is located at the back of the TV. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the TV and a table. +20-5 Rear Front Tidying cables Gather and bind the cables with the supplied cable tie. NOTE The Kensington security system is optional. You can obtain additional accessories from most electronics stores. Detaching the Stand 3 Pull out the Stand Body from the TV. M1931D 19MA31D 1 Place the TV with the screen side down on a flat and cushioned surface. CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen detaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 2 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. 3 Remove 2 screws and pull out the Stand Body from the TV. M2631D 1 Place the TV with the screen side down on a flat and cushioned surface. CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen detaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 2 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. M1931D/19MA31D M2631D VESA (A x B) 75 x 75 100 x 100 Standard screw M4 M4 Number of screws 4 4 Wall mount bracket (optional) RW120 10 cm 10 cm 10 cm 10 cm yyVESA (A x B) AB If you intend to mount the TV to a wall, attach Wall mounting interface (optional parts) to the back of the TV. When you install the TV using the wall mounting interface (optional parts), attach it carefully so it will not drop. 1 Please, Use the screw and wall mount interface in accordance with VESA Standards. 2...
Other models in this manual:Displays - M1931D-PZ (2.92 mb)
Displays - M2631D-PZ (2.92 mb)
Televisions - M1931D (2.92 mb)
Televisions - M2631D (2.92 mb)