Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Press the corresponding button on the remote control to select the correct input source. Input button guide: 1 TV key Toggle Analog TV (ATV) between input sources. 2 AV key Toggle AV and HDMI between input sources. 3 SCART key Toggle SCART between input sources. 4 PC key Toggle VGA between input sources. * For VGA input, Philips recommends setting your PC’s external monitor resolution to 1440 x 900 pixels @ 60 Hz refresh rate. Y w w R R Y D-Sub D-Sub SPDIF-OUT PC AUDIO-IN 8 1 2 3 4 OSD navigation Many of the advanced settings and adjustments are available through using the OSD (onscreen display) menus, as shown in the example screenshot below. Basic operations required to navigate these menus (Picture, Audio, Channel management and Settings) are described in this section. Navigating the OSD with the remote control There are four main OSD menus. These are: Picture, Audio, Channel management and Settings. Use the following method to navigate these menus. 1 Press the MENU button on the remote control or the MENU button on the control panel. 2 Select your desired menu by using the up and down directional keys to switch between the four menus. 3 Use the directional keys to interact with the menu. The up / down directions will scroll through the menu options, while left/right will adjust the different settings (for example, in the Picture menu, settings such as brightness, contrast, etc.). Press MENU to exit. Adjusting the OSD settings The OSD can be used for adjusting the settings of your TV Monitor. Press the MENU a key to open the OSD. You can use the OSD to adjust the picture quality, audio settings,channel settings and general settings. For advanced settings, please refer to following page: Adjusting the picture quality 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select Picture from the OSD. Then navigate to the picture element you wish to adjust. 3 Use the left or right keys to adjust the sliding scales. 4 The Picture menu can be used to adjust the brightness, contrast, colour, sharpness and other image-related qualities. Picture Brightness Colour Contrast Noise Reduction Sharpness Colour Temp Backlight 50 60 30 80 70 Warm Low Move Enter Back Picture Brightness Colour Contrast Noise Reduction Sharpness Colour Temp Backlight 50 60 30 80 70 Warm Low Move Enter Back 9 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select Audio from the on screen display. Then navigate to the feature you wish to adjust. 3 Use the left or right keys to adjust the sliding scales.Press OK to save. 4 Adjusting the audio settings The Audio menu can also be used to adjust the treble, bass, balance, sound effect and AVL Adjusting the channel management 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select Channel management from the OSD. 3 Use the directional keys to navigate the menus. 4 The Channel management menu can be used to set the channel namings, Auto Scan,Manual Scan channel and other related settings. Adjusting the settings 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select Settings from the OSD. Then navigate to the feature you wish to adjust. 3 The Settings menu can be used to adjust the menu language and other important settings. Advanced features Lock This Channel Lock This Channel allows you to enter a password and effectively stop anyone without the password from watching TV Monitor Channel. Audio Treble Balance Bass Sound Effect AVL 50 60 30 Off Off Move Enter Back Channel Management Country Reorder Skip Manual Scan Name Auto Scan Frequency Germany Off 639. 22Mhz Move Enter Back Lock This Channel Setting s Menu Language Set PIN Sleep Wide Mode Factory Default English Off Full Move Enter Back * The options available on the OSD may vary depending on the TV Monitor signal source. 10 To enable this feature: Setting a personal PIN 1 Press the MENU key on the remote control to bring up the OSD. 2 Use the directional keys to navigate to the Settings menu. Then select Set PIN . (see note) 3 Enter a four-digit password. Type it again and press OK to reconfirm. 4 Press MENU to exit. Locking TV Channel 1 Press the MENU key on the remote control to bring up the OSD. 2 Use the directional keys to navigate to the Channel Management menu. Then select Lo.ck This Channel 3 Enter your PIN. Type it again and press OK to reconfirm. (see page 10 note) Settings Menu Language Sleep Wide Mode Factory Default English Off Full Move Enter Back Channel Management Country Reorder Skip Manual Scan Name Auto Scan Frequency Germany Off 639. 22Mhz Move Enter Back 11 Set PIN Lock This Channel * The default PIN for this TV Monitor is "0000." First enter "0000" when you want to change the PIN. If youforget your PIN, please enter 6163 to reset. Reorder for channels The first time you completed the setup wizard, all available channels were listed. If you need to reorder for new channels, please follow the steps below: Reordering for channels 1 Press ...