4 Press [Back/PP] to return to TV Setup Menu. 5 Press [Back/PP] to exit. Reset to factory settings Resetting your TV to factory settings restores default picture and sound settings. Channel installation settings remain the same. 1 Press [Home/Menu] ] > [TV Setup>. 2 Select [Setup] > [TV settings] > [Factory settings] , then press OK. TV settings are reset back to the factory default. Reinstall TV Starts a TV initialization to reset all settings to default and replace (reinstall) all channels. 1 Press [Home/Menu] ] > [TV Setup> [OK]. 2 Select [Setup] > [TV settings] > [Reinstall TV], then press OK. TV will perform a power down cycle going into standby and then starts-up again. If the TV stays in Standby mode, wake TV up with switch on button on remote control. 1 Region OSD is displayed: Region Australia Europe Select [Europe] and press . 2 Select language OSD is displayed: Select [xxxx] (i.e. language from list) and press . 3 Select install country OSD is displayed: Select [xxxx] (i.e. country from list) and press . 4 Select TV placement OSD is displayed: [Wall mounted]: in case of wall mounting [On a TV stand]: in case of stand and press . 5 Select TV location OSD is displayed: [Home]: Always select this [Shop]: Shop mode, not to be used and press . 6 Universal access for the visual and hearing impaired OSD is displayed: [No]: No special settings [Yes]: Special settings configured and press . 7 Press [Settings] to continue and install channels. Perform the following steps: [Install TV channels] and press [Continue] [Settings] A screen is displayed to make changes to set the channel list/map configuration: [Symbol rate mode]: Automatic TV will use the preset Symbol rate (6.900/6.875) Manual Option to set Symbol rate 1 and Symbol rate 2 [Symbol rate 1]: 0.000 (to set) [Symbol rate 2]: 0.000 (to set) [Frequency scan]: Quick scan Install channels based on a pre-configured data table Full scan Install channels based on scanning the whole frequency spectrum [Frequency step]: 1 MHz With Full scan, step size to search for channels is 1 MHz 8 MHz With Full scan, step size to search for channels is 8 MHz [Network Frequency Mode]: Automatic TV will set the Network frequency based on a pre- configured data table Manual Option to set Network frequency [Network Frequency]: 000.00 (to set) [Analogue channels]: On TV will scan also analogue channels Off TV will not scan analogue channels [LCN Sorting]: On TV will scan also analogue channels Off TV will not scan analogue channels [Reset]: On [Done]: Once finished select [Done] and press 8 Press [Start] to continue. 9 If a preset Network Frequency is not available, or the Network Frequency Mode is set as manual, Enter the Network Frequency and press [Done] to continue. Press [Cancel] if no DVB-C to install (only DVB-T and Analogue). 10 Once the channel list is configured, the TV shows how many digital and analog channels are captured and returns to the TV Setup OSD. 11 Press [Done] > [Skip] > [Finish] > [Close] to return to the TV Setup Menu. If PBS Mode is [On], the Guest menu is displayed. More Channel Settings 1 Press [Home/Menu] > [TV Setup]> [OK]. 2 Select [Setup] > [Channel settings], then press OK. 3. Select a setting to adjust and press : • [Languages]: Set the required DVB languages. • [Primary audio]: Sets the Primary audio channel to the selected country language. • [Secondary audio]: Sets the Secondary audio channel to the selected country language. • [Primary subtitles]: Sets the Primary subtitles to the selected country language. • [Secondary subtitles]: Sets the Secondary subtitles to the selected country language. • [Primary text]: Sets the Primary text to the selected country language. • [Secondary text]: Sets the Secondary text to the selected country language. • [Visually impaired]: Sets the feature Visually impaired to support: [Off]: [Speakers]: [Headphones]: [Speakers + headphones]: • [Preferred audio format]: Sets the feature preferred audio format: [Standard]: [Advanced]: • [Mono/Stereo]: Sets the feature audio format: [Mono]: [Stereo]: Press OK to confirm your choice. Channel installallation Before starting to install channels specific settings must be set to get the channels to be installed (see reinstall, page 29) 1 Press [Home/Menu] > [TV Setup]> [OK]. 2 Select [Setup] > [Channel settings], then press OK. 3. Select a setting to adjust and press : • [Channel installation]: Configure the proper installation settings: • [Automatic Channel Update]: This TV can automatically rescan the entire channel configuration once every day if this feature is set and the TV is in Standby mode. [Off]: No automatic updating [On]: At TV clock 5.00 AM channel updating starts • [Channel Update Message]: Once the TV has updated its channel list due to an Automatic Channel Update, this OSD will inform about the occurrence [Off]: No updating message [On]: After an update cycle an OSD message will be displayed once the TV is switch...
