Votes - 2, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock User’s Manual Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. • Do not use a damaged or loose plug. • This may cause an electric shock or fire. • Do not pull the plug out by the wire nor touch the plug with wet hands. • This may cause an electric shock or fire. • Use only a properly grounded plug and recepticle. • An improper ground may cause electric shock or equipment damage • Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. • Failure to do so may cause an electric shock or fire. User’s Manual Safety Instructions • Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. • Failure to do so may cause an electric shock or fire. Power • Do not connect too many extension cords or plugs to an outlet. • This may cause a fire. User’s Manual Safety Instructions Installation • Do not cover the vents on the monitor cabinet. • Bad ventilation may cause a breakdown or fire. • Put your monitor in a location with low humidity and a minimum of dust. • An electric shock or fire could result inside the monitor. • Do not drop the monitor when moving it. • This may cause damage to the product or human body. • Place the monitor on a flat and stable surface. • The monitor can cause injury by falling. • Set down the monitor carefully. • It could be damaged or broken. User’s Manual Safety Instructions Installation • Do not place the monitor face down. • The TFT-LCD surface may be damaged. User’s Manual Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightlymoistened, soft fabric. • Do not spray detergent directly on the monitor. • Use the recommended detergent with a smooth cloth. • If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. • A dirty connector can cause an electric shock or fire • Do not set a glass of water, chemicals or any small metal objects on the monitor. • This may cause damage, electric shock or a fire. • If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. User’s Manual Safety Instructions • Do not remove cover(or back). No user serviceable parts inside. • This may cause an electric shock or a fire. • Refer servicing to qualified service personnel. Other • If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. • This may cause an electric shock or a fire. • Do not place any heavy objects on the monitor. • This may cause an electric shock or a fire. • For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. • This will reduce eye fatigue. • Do not use or store inflammable substances near the monitor. • This may cause an explosion or fire. User’s Manual Safety Instructions Other • Do not try to move the monitor by pulling on the wire or the signal cable. • This may cause a breakdown, electric shock or a fire due to damage to the cable. • Do not move the monitor right or left by pulling only the wire or the signal cable. • This may cause a breakdown, electric shock or a fire due to damage to the cable. • Never insert anything metallic into the monitor openings. • This may cause an electric shock, fire or injury. User’s Manual Introduction Unparking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Monitor and Stand Power Cord Signal Cable Quick Setup Guide Warranty Card (Not available in all locations) User's Guide and Driver Installation CD User’s Manual Introduction Front 1. Auto button / Use this button to auto adjustment direct access. / Exit button Use this button to Exit the active menu or the OSD. 2. Menu button These buttons allow you to highlight and adjust items in the menu. 3. Power button Use this button to turn the monitor on and off. 4. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 5. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. User’s Manual Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port : Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal cable : Connect the end of the signal cable to your computer's ...
Other models in this manual:Displays - 72V (1.87 mb)