Votes - 2, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. Trun on power switch. 2. There are 3 ways to connect the signal cable to your monitor. Choose one of the followings : 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, RGB port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI(HDCP) port on the back of your monitor. 2-3. Using the BNC (Analog) connector on the video card. Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V port on the back of your Monitor and the 15 pin D-sub Port on the computer. DVI cable or BNC cable is optional. 3. Connect the audio cable for your monitor to the audio port on the back of your computer. 4. Turn on both your computer and the monitor. Contact a local Samsung Electronics Service Center to buy optional items. 2. Connecting to a VCR 1. AV input devices like VCRs or Camcorders are connected to the AV IN [VIDEO] or AV IN [S-VIDEO] of the monitor using the S-VHS or BNC cable. S-VHS or BNC cable is optional. 2. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the monitor's AV AUDIO IN [L-AUDIO-R] using audio cables. 3. Select AV or S-Video that is connected to a VCR or Camcorders using the Source button on the monitor's front or remote control. 4. Then, start the VCR or Camcorders with a tape inserted. 3. Connecting to a DVD Player 1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor and the AUDIO OUT jacks on the DVD player. 2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor and the PR, Y, PB jacks on the DVD player. Component cable is optional. 3. Select Component that is connected to a DVD player using the Source button on the monitor's front or remote control. 4. Then, start the DVD Player with a DVD disc inserted. For an explanation of Component video, see your DVD player owner's manual. 4. Connecting a Camcorder 1. Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor. 2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the Monitor. 3. Select AV that is connected to a Camcorder using the Source button on the monitor's front or remote control. 4. Then, start the Camcorders with a tape inserted. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. 5. Connecting DTV Set Top Box The connections for a typical Set Top Box are shown below. 1.Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor and the AUDIO OUT jacks on the Set Top Box. 2.Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor and the PR, Y, PB jacks on the Set Top Box. 3.Select Component that is connected to a DTV Set Top Box using the Source button on the monitor's front or remote control. For an explanation of Component video, see your Set Top Box owner's manual. 6. Connecting Speakers 1. Tighten the SET and the speaker using the screws. * Mount the set of the speaker without the speaker stand. 2. Connect the speaker connection cable between the speaker connection jack on the rear of the SET and the speaker connection jack on the rear of the speaker. Do not move the SET holding the speaker when the SET is connected to the speaker. The speaker-bracket for connecting the SET speaker my be damaged. 7. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the MONITOR OUT [L-AUDIO-R] on the Monitor. 8. Connecting the LAN Cable 1. Connect the LAN cable. 9. Connecting USB 1. You can connect to USB devices such as a mouse or keyboard. 10. Connecting the Digital Audio System 1. Connect a set of digital audio cables between the Digital Audio Input jacks on the DIGTAL AUDIO SYSTEM and the DIGITAL AUDIO OUT on the Monitor. 1. Introduction 2. Beginning : Main Screen | Port Setting | 3. Power Control 4. Input Source Control 5. Image Size Control : PC, BNC, DVI | AV, S-Video, Component, DVI(HDCP) 1. Introduction 6. Time Control 7. PIP Control : PIP Size | PIP Source 8. Settings Control : Picture | Picture PC | Audio | Image Lock | 9. Maintenance Control - Lamp Control 10. Maintenance Control - Scroll 11. Maintenance Control - Video Wall 12. Troubleshooting 13. Settings Value Display In Multiple Display Mode A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cabl...
Other models in this manual:Displays - 460P (7.13 mb)