Votes - 3, Average rating: 3.7
(
)
)
|
Other manuals for this model:
manual abstract
Now you can remove the stopper pin to adjust the stand. - Caution Avoid lifting the product holding only the stand. Disassembly is in the reverse order of assembly. © Installing the Product 2-2 2-3 Installing a Wall Mount Before installation, disassemble the product according to the following steps. Lift up the monitor stand to the maximum angle with your left hand, and remove the back decoration cover with your right hand, as shown in the figure. Remove the two screws(A). © rp Remove the stand arm in the direction shown in the figure. This product provides a wall mount of 100 mm x 100 mm(200 mm x 100 mm) that complies with the VESA specifications. 100 mm x 100 mm 200 mm x 100 mm A. Wall Mount Base B. Wall Mount Kit (Optional) 1. Turn the product off and unplug the power cord from the wall outlet. 2. Place a soft cloth or cushion on a flat surface to protect the panel and place the product face down. 2-3 Installing the Product 3. Separate the stand. 4. Align the groove of the Monitor's wall mount base with the groove in the wall mount ki and firmly fix the wall mount kit by fastening the screws. O' If you use a screw that is longer than the standard specifications, the inside of the product may be damaged. •For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the corresponding specifications. •Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force. This may result in damage to the product or injury due to the product falling. Samsung shall not be held liable for any damage or injury. •Samsung shall not be held liable for any damage to the product or injury caused by using a stand that is not compatible with the specified specifications or due to an installation not performed by an authorized installation engineer. •When installing the product using a wall mount, purchase a wall mount that provides at least 4 inches (10 cm) of space from the wall. •Samsung shall not be held liable for any problems caused by using a stand that is not compatible with the specified specifications. •Use a wall mount according to specifications of your country. Installing the Product 2-3 2-4 Connecting to your Network The connecting part may differ depending on the product model. Connect between the [LAN] port on the product and your network using a LAN cable. R* The two [LAN] ports are designed to work as an Internet HUB. One port can be used for input and the other port for output to connect the product to an external Internet device. Both ports can be used for either input or output. • Use Cat5(*STP Type) cable for the connection. *Shielded Twist Pair (NC190 Only) 2-4 Installing the Product 2-5 Connecting Power To use the product, connect the power cable to a power outlet and the [POWER] port on the product. (The input voltage is switched automatically). Installing the Product 2-5 2-6 Connecting to another Monitor Please select the right connection method for your monitor. • When using the [RGB OUT] port • Connect between the [RGB OUT] port on the product and the D-Sub port on your monitor using a D-Sub cable. • When using the [DVI OUT] port • Connect between the [DVI OUT] port on the product and the DVI port on your monitor using a DVI cable. Connect to the [DVI OUT], [RGB OUT] port to display the same picture on another monitor such as the projector. (For presentation purposes) 2-6 Installing the Product 2-7 Connecting with a PC Connect the [RGB IN] port of the product to the [D-Sub] port of your PC with a D-Sub cable. Use the [RGB IN] port to directly connect the monitor to a PC. Installing the Product 2-7 2-8 Connecting a Stereo Cable Connect the [AUDIO IN] port on the rear side of the monitor to the sound card of the PC. 2-8 Installing the Product 2-9 Connecting USB The port supports up to USB 2.0. Connect USB devices such as a mouse, keyboard and external storage devices (DSC (Digital Still Camera), MP3, external storage, etc.). VMware View 4.6 or later is required. Data transfer rate may decrease depending on the network conditions. Installing the Product 2-9 2-10 Connecting Headphones Connect your headphones to the Headphone connection terminal. 2-10 Installing the Product 2-11 Connecting MIC Connect the microphone cable to the MIC port on the monitor. Installing the Product 2-11 2-12 Kensington Lock A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device. You have to purchase an additional locking device. Locking the product 1. Insert the locking part of the locking device into the hole of the Kensington lock of the product (J* ) and turn i...
Other models in this manual:Displays - NC190 (1.46 mb)
Displays - NC190-T (1.46 mb)
Displays - NC240 (1.46 mb)
Displays - NC240M (1.46 mb)