Votes - , Average rating:
(
)
)
Manafacture: Samsung
File size: 8.29 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
Other manuals for this model:
manual abstract
A. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger. 1. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. 2. Be careful when installing the product on the bracket as fingers can be caught in the holes. 3. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A. Monitor B. Wall Bracket C. Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2°before installing it on the wall. 1.Fix the product to the wall bracket. 2.Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. 3.You can adjust the bracket angle between -2°and 15 °. Make sure to use the top center, and not the leftor the right side of the product to adjust the angle. Select Language Main Page Model Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Connections Installing the Stand KIT Note • Only the supplied bolts should be used. Caution Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Installing the Semi Stand Left stand Right stand Caution Make sure to install the stand with the Caution label folded backwards. 1) To protect your product, a Cover Hole is included as an accessory. This protects the hole at the bottom of the monitor where the stand is inserted. If you install a wall mount kit for your monitor, please place the Cover Hole over it. 2) Insert it into the hole at the bottom of the monitor. Insert the screw provided with the Cover Hole into the marked place and fasten it firmly. Caution The resolution may differ for each product model. For information on the optimal resolution, refer to the user manual. Connecting the LCD Display Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note • AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User Controls under Adjusting Your LCD Display. Connecting a Computer 1) Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Trun on the power switch. 2) There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: 2-1) Using the D-sub (Analog) connector on the video card. Connect the D-sub to the 15-pin, RGB port on the back of your LCD Display and the 15 pin D- sub Port on the computer. 2-2) Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI(HDCP) port on the back of your LCD Display and the DVI port on the computer. 2-3) Using the BNC (Analog) connector on the video card. Connect the BNC Cable to the BNC/COMPONENT IN -R, G, B, H, V ports on the back of your LCD Display and the 15 pin D-sub Port on the computer. 3) Connect the audio cable for your LCD Display to the audio port on the back of your computer. Note • Turn on both your computer and the LCD Display. Note • The DVI cable or BNC cable is optional. Contact a local Samsung Electronics Service Center to buy optional items. Connecting a VCR 1) AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable. 2) Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the LCD Display 's AV AUDIO IN [L-AUDIO-R] using audio cables. Note • Select AV or S-Video for a connected VCR or Camcorder using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the...
Other models in this manual:Displays - 400DX (8.29 mb)
Displays - 460DX (8.29 mb)
Displays - 460DXN (8.29 mb)
- ()