Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
LOAD FACTORY This is selected when the factory settings are to be restored. When any changes are made to the settings on this menu, the changes also take effect for the settings of other linked video signals for some of the video signals which have been selected. How the changes are linked is explained below. . Any changes made to the settings when the LINE A signal has been selected will also be made to the LINE B signal. Conversely, any changes made to the settings when the LINE B signal has been selected will also be made to the LINE A signal. . When the optional SDI input unit (BT-YA210G) is installed, any changes made to the settings when the CMPNT 480i signal is selected will also be made to the SDI signal. Conversely, any changes made to the settings when the SDI signal is selected will also be made to the CMPNT 480i signal. How to use the on-screen menus . VIDEO CONFIG menu The menu items shown below appear when the VIDEO CONFIG menu is selected on the main menu. [VIDEO CONFIG] ASPECT ASPECT 16:9 An aspect ratio of 4:3 or 16:9 can be set. COMPONENT LEVEL SMPTE The underscanning function cannot be used when 16:9 has been selected. COMPONENT LEVEL The component input level is selected here. This menu item appears only when the component signal has been selected as the input signal. . SMPTE Select this when signals from a DVD or MII VTR are supplied. . B75 Select this when signals with a 7.5% setup level are supplied from a Betacam VTR. . SYSTEM CONFIG menu The menu items shown below appear when the SYSTEM CONFIG menu is selected on the main menu. [SYSTEM CONFIG] BACKLIGHT 60 STATUS DISPLAY CONTINUE [INPUT SELECT] LINE B ON CMPNT ON SDI ON REMOTE OFF BACKLIGHT The backlight brightness is adjusted to a value from 0 to 60 here. 60 is the factory setting. STATUS DISPLAY The information displays during input switching and input signal system display are set here. . CONTINUE The information remains displayed. This is the factory setting. . 3 SEC OFF The information is displayed for 3 seconds, after which it is cleared from the display. . OFF No information is displayed. INPUT SELECT LINE B By setting this item to OFF, LINE B can be skipped. CMPNT By setting this item to OFF, CMPNT can be skipped. SDI By setting this item to OFF, SDI can be skipped. This item is valid only when the optional SDI input unit (BTYA210G) is installed. REMOTE External control is set to ON or OFF here. How to use the on-screen menus . MAINTENANCE menu The menu item shown below appears when the MAINTENANCE menu is selected on the main menu. [MAINTENANCE] RUNNING TIME The total running time of the monitor is displayed here (in RUNNING TIME 300H hours). REMOTE specifications In order to perform REMOTE operations, select ON as the setting for the REMOTE menu item on the SYSTEM CONFIG menu. The functions for REMOTE operations can be switched by opening or shorting the pins corresponding to the functions to pin 5 (ground). There are two kinds of operations: level operations and edge operations. Level operations : The functions are operational while the pins are shorted to pin 5 (GND). Edge operations : The functions become operational when the pins are transferred from an open-circuited to short-circuited state vis-a-vis pin 5 (GND). The following four functions can be controlled externally. . Input switching function (edge operations) This switches the input from LINE A, LINE B, CMPNT or SDI. The SDI signal input can be selected only when the BT-YA210G, available as an optional accessory, is installed. The input signals which have been set to OFF (which are to be skipped) under the INPUT SIGNAL menu item on the SYSTEM CONFIG menu will not be displayed, thus making it impossible for them to be selected. . Aspect ratio switching function (level operations) This switches the aspect ratio. . Standby function (level operations) This blacks out the monitor while the power is on in order to prevent images from being burned onto the screen. . Tally function (level operations) This enables the tally lamp to light up red. The tally lamp operates regardless of whether ON or OFF is selected as the REMOTE menu item setting. 5 4 3 2 1 9 8 7 6 Connector (9P) Pin No. Signal 1 Input switching function 2 Aspect ratio switching function 3 Standby function 4 Tally function 5 GND 6 s 7 s 8 s 9 s About the stand The stand attached to the unit can be tilted forward 10° and back 20°. When tilting the monitor, firmly press down on the stand and grasp the top part of the monitor. Further, it is recommended to secure the stand using the screw holes when it is to be permanently located.