Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
3. Always disconnect power (electric units) before disassembling, repairing or changing attachments on the unit. 4. Follow all safety codes as well as the Occupational Safety and Health Act (OSHA). 5. Ensure safety devices are operating properly before each use. DO NOTremove or modify any part of the gun or unit. 6. Know how to stop this unit and relieve pressure quickly. Be thoroughly familiar with the controls. 7. Stay alert - Watch what you are doing. DANGERWARNINGCAUTIONNOTE: Information that requires special attention.Important Safety Instructions SAVE THESE INSTRUCTIONSWhen using this product, basic precautions should always be followed, including the following: DANGER8. Do not operate this unit when fatigued or under the influence of alcohol or drugs. 9. Keep operation area clear of all persons. 10. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 11. Follow maintenance instructions specified in this manual. 12. This product shall be connected to a power supply receptacle protected by a ground fault circuit interrupter (GFCI) (electric power washers only). 13. If product is provided with a GFCI, be sure to inspect the cord and GFCI prior to use. Any repair or replacement of the power cord must be performed by a qualified (licensed or certified) electrical technician.WARNINGRisk of injection or severe injury. Keep clear of nozzle. Do not discharge streams at persons. This product is to be used only by trained operators. Always remove lance from gun before cleaning debris from tip.• Keep clear of nozzle. NEVERdirect high pressure spray at any person, animal or self. • Always wear safety goggles or glasses and protective clothing when operating, performing maintenance or changing accessories. • Neverput hands or fingers over the spray tip while operating the unit. • Nevertry to stop or deflect leaks with any body part. • Always engage the trigger safety latch in the safe position when spraying is stopped even if only for a few minutes. • Always follow detergent manufacturer's label recommendations for proper use of detergents. Always protect eyes, skin and respiratory system from detergent use. SAFETY & WARNING INSTRUCTIONS Keep hose away from sharp objects. Bursting hose may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose. TROUBLE SHOOTING 9 WARNINGDo notuse pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Ensure that all equipment and accessories are rated to withstand the maximum working pressure of the unit. WARNINGExplosion hazard. • NEVERspray flammable liquids or use pressure washer in areas containing combustible dust, liquids or vapors. • NEVERoperate this machine in a closed building or in or near an explosive environment.WARNING• Do notspray electrical apparatus or wiring. • NEVERdisconnect the high pressure discharge hose from the machine while the system is pressurized. To depressurize the machine, turn the power and water supply off, then press the gun trigger 2-3 times. • NEVERpermanently engage the trigger mechanism on the gun. • NEVERoperate the machine without all the components properly connected to the unit (gun/lance assembly, nozzle, WARNING• Always hold gun and lance firmly when starting and operating the machine. • NEVER allow the unit to run with the trigger released (OFF) for more than one minute. Resulting heat buildup will damage pump. • NEVERstore the pressure washer outdoors or where it could freeze. The pump will be seriously damaged. • Release trigger when changing from high to low pressure modes. Failure to do so could result to damage to the nozzle. • This unit must always be used in the horizontal position.CAUTIONEquipment damage. • ALWAYSturn water supply " ON" before turning the pressure washer "ON" . Running pump dry causes serious damage. • Do not operate the pressure washer with the inlet water screen removed. Keep screen clear of debris and sediment. • NEVERoperate pressure washer with broken or missing parts. Check equipment regularly and repair or replace worn or damaged parts immediately. • Use only the nozzle supplied with this machine. • Never leave the lance unattended while the machine is running. • Never attempt to alter factory settings. Altering factory settings could damage the unit and will void the warranty. 2PROBLEM POSSIBLE REASON POSSIBLE SOLUTION PRESSURE WASHER WILL NOT START WHEN THE ON/OFF SWITCH IS IN THE "ON" POSITION 1. Electrical socket is faulty or breaker has tripped. 2. Voltage is inadequate. 3. GFCI has tripped. 4. Power cord is not plugged in. 1. Check plug, socket, fuses, breaker. 2. Check that the voltage is adequate. 3. Reset/ Try another electrical outlet. 4. Plug in power cord. PUMP DOESN'T REACH ADEQUATE PRESSURE OR CAVITATES 1. Water intake filter is clogged. 2. Pump is drawing air. 3. Diameter of garden hose is too small. 4. Water supply is restricted. 1. Remove and cl...