Votes - 2, Average rating: 4
(
)
)
|
manual abstract
No grounding means are provided for a double-insulated product, nor should grounding means be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the original parts. A double-insulated product is marked with the words “Double Insulation” or “Double Insulated.” Product may also be marked with symbol shown below. Double Insulated symbol Do not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Ensure all equipment and accessories are rated to withstand the maximum working pressure of the unit. Explosion hazard. • NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids or vapors. • Never operate this machine in a closed building or in or near an explosive environment Do not spray electrical apparatus and wiring. • Never disconnect the high pressure discharge hose from the machine while the system is pressurized. To depressurize machine, turn power and water supply off, then press gun trigger 2-3 times. • Never permanently engage the trigger mechanism on the gun. • Never operate the machine without all components properly connected to the machine (handle, gun/wand assembly, nozzle, etc.). Equipment damage. • ALWAYS turn water supply “ON” before turning pressure washer “ON.” Running pump dry causes serious damage. • Do not operate the pressure washer with the inlet water screen removed. Keep screen clear of debris and sediment. • NEVER operate pressure washer with broken or missing parts. Check equipment regularly and repair or replace worn or damaged parts immediately. • Use only the nozzle supplied with this machine. • Never leave the wand unattended while the machine is running. • Never attempt to alter factory settings. Altering factory settings could damage the unit and will void the warranty. • Always hold gun and wand firmly when starting and operating the machine. • NEVER allow the unit to run with the trigger released (off) for more than one (1) minute. Resulting heat buildup damage pump. 4 Instrucciones de montaje y lista de piezas PW1750 Lista de Repuestos Para Ordenar Repuestos o Asistencia Tecnica, sirvase llamer al 1-800-330-0712 (En los Estados Unidos, o llame a su distribuidor local) Sirvase proporcionar la siguiente informacion: 16 - Numero de serie (si lo hubiera) - Numero de modelo 9 8 - Descripcion y numero del repuesto, segun se indica en la lista de repuestos. 16 7 Dirija toda la correspondencia a: 10 11 Campbell Hausfeld Attn: Customer Service 6 100 Mundy Memorial Drive Mt. Juliet, TN 37122 U.S.A. 5 14 4 16 2 15 3 1 No. de Numero del Ref. Descripcion Repuesto Ctd. 1 Adaptador de pivote PM350100SV 2 Filtro PM350101SV 3 Entrada N/ A 4 Interruptor N/ A 5 Soporte de la pistola PM350111SV 6 Limpiador de puntas PM008500AV 7 Boquilla turbo PM350108SV 8 Lanza de rociado en abanico ajustable PM350104SV 9 Pistola PM350109SV 10 Manguera PM350110SV 11 Soporte para la manguera PM350112SV 12 Mango PM350114SV 13 Soporte del cable electrico PM350113SV 14 Salida N/ A 15 Botella para detergente PM350105AV 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 16 Anillo en O PM232200SV 3 33 Sp Instrucciones de montaje y lista de piezas PW1750 Interruptor de encendido/apagado (ON/OFF) Lanza Entrada de agua Pistola Enchufe GFCI Salida de agua Manguera de alta presion Manguera Adaptador de jardin de pivote Figure 6 Notas Operating Instructions and Parts List PW1750 • Pressure washer is not meant to pump hot water. NEVER connect it to a hot water supply as it will significantly reduce the life of the pump. • NEVER store the pressure washer outdoors or where it could freeze. The pump will be seriously damaged. • Release trigger when changing from high to low pressure modes. Failure to do so could result in damage Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose. Garden Hose Connection Instructions 1. Attach swivel adapter to pump water inlet, if not already attached. Notice the swivel adapter is marked with the words pump and hose. Make sure to connect pump side of adapter to pump water inlet to prevent damage to the threads. 2. Attach garden hose to swivel adapter side marked hose. 3. The spray gun should be locked into the "OFF" position by locating the safety trigger lock just above the trigger of the gun. Activate the lock by holding the gun and push the lock from left to right. Squeeze trigger to make sure the trigger does not move. The safety trigger lock should be locked at all times when pressure washer is not in use. Power Cord 1. Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 3. 2. THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET. Reset Figure 3 - Grounded plug...