Votes - 3, Average rating: 4.3 ( )

Manafacture: Nilfisk-ALTO File size: 3.38 mb File name: Language of manual:

Apply Car Combi Cleaner with the foam sprayer. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min. 2. Wash the car with the car nozzle, which has been optimized for quick and gentle cleaning of enamelled surfaces (the jet is wider and not so sharp). Start at the front of the car and work back- wards to avoid water from penetrating by the door mouldings. 3. Use the brush for removal of traffi c film which is not removed by the nozzle. If the car is very dirty, apply Car Combi Clean er again. 4. Attach the undercarriage nozzle and clean undercarriage and wheel arches. 5. Remove water from the surface of the car with the scraper on the car brush. Make sure that all grains of sand etc. have been removed before using the scraper. Wipe with a wash lea- ther where the scraper cannot reach. Rims, alu- minium Rim brush, auto nozzle, atomizer, Alu Cleaner Apply Alu Cleaner with an automizer. Let it act for approx. 5 min. and wash with the rim brush. For steel rims, use Car Com- bi Cleaner. Use the foam sprayer and wash with rim brush. Be careful! The high pressure jet may damage the tyres. Flag- stones, concrete fl oors and other hard surfaces Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Wash towards outlets or the like. On surfaces with moss or algae you may start by applying Stone & Wood Cleaner with the foam sprayer. Wash before the soap dries. Another more effective and quicker method is to use the Patio Cleaner. Thus you will also avoid splashes. Garden furniture, wood Wood Cleaner Garden brush Apply Wood Cleaner and wash before the soap dries. NOTE: Use the garden brush to clean off the dirt. Brickwork, Wood work Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Same method as for flagstones, but be careful -bad joints and wood may be damaged by high pressure.You may choose only to use the Tornado® nozzle. Adjust the distance (pressure) to the quality of the joints and the wood. Patio Cleaner can also be used on vertical surfaces. Gutter Underchassis spray lance Wash the gutter with the nozzle. Always wash towards downpipes. Beware not to spray under the roofing. Cleaning of drain pipes, out- lets, down pipes etc. Tube cleaner Push the tube cleaner approx. . m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the „plug“ and flush the dirt backwards. Rust, paint Water/sandblasting equipment Mount the water/sand blasting equipment and rust and paint is efficiently and quickly removed. Beware not to damage the surface to be sandblasted. Green- house Tornado® PR nozzle brush, Stone & Wood Cleaner Wash with high pressure and maybe a brush. You may use Stone & Wood Cleaner to remove moss and algae. Garden tools, lawn mover Tornado® PR nozzle, Power- speed® nozzle, multiangle adaptor, Metal Cleaner Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with the foam sprayer and let it act for approx. 5 min. Wash with the nozzle. You may use the multiangle adaptor for hard to get at areas to avoid splashing. 11 12 .. 6 After using your pressure washer 6.2 Winding up of electric cable and high pressure hose carefully up. 1. Wind up the electric cable on the appropriate hooks. Builtin clip for good holding (1). The lower hook can be turned to release the electric cable. 2. The high pressure washer comes in two models: A) with hook for storage of high pressure hose (14) - B) with a hose reel (13). 6.1 Storing the washer The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (turn the start/stop switch (1) to position “O” and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray gun. 3. Stop the machine, unplug and wind up hose and cable. 4. Place spray handle, nozzles and other accessories in the holders of the machine. Should the machine by mistake be frozen, it will be necessary to check it for damage. NEVER START-UP A FROZEN MACHINE. Frost damages are not covered by the guarantee! 6.3 Storage of accessories The standard accessories (spray gun (f), spray lance (a), nozzles (b) foam sprayer (c)) can be stored on the pressure washer. The nozzle cleaning tool (d) and a Click & Clean brush (e) can also be stored on the product. To avoid accidents, the electric cable and the high pressure hose should always be winded a b c d e f a + f 7 Maintenance 7.1 Cleaning of water inlet fi lter 7.2 Cleaning of nozzle 7.3 Cleaning of machine vents 7.4 Greasing of couplings WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice: • Wash out water hose, high pressure hose, spray lance and accessories before mounting. The machine shou...

Download now

Please, enter two numbers from picture: