Votes - , Average rating:
(
)
)
Manafacture: DeVillbiss Air Power Company
File size: 1.61 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
engine that has been exposed to thermal heat for a long period of time. Fuel valve closed Move the fuel valve lever to the “Open” position. No or low Spray wand not in high pressure. See How to Use Spray Wand pressure instructions in the Operation (initial use) Section. Low water supply. Water supply must be at least 5 GPM @ 20 PSI (137.9 kPa). Leak at high pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Water filter screen clogged. Remove and clean filter. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re- con nect water source to pump inlet and turn on wa ter source. Squeeze trigger to remove remain ing air Air in hose. Choke lever in the “Choke” position. Move choke to the “No Choke” po si tion. High pressure hose is too long. Use high pressure hose under 100 feet. AWSC = Authorized Warranty Service Center 17 - ENG A16091 PROBLEM CAUSE CORRECTION Will not draw chemicals Spray wand not in low pressure. Chemical screen not in cleaning solution. Chemical too thick. Pressure hose is too long Chemical build up in chemical injector. Chemical filter clogged. See How to Use Spray Wand paragraph in the Operation Section. Clean filter. Dilute chemical. Chemical should be the same consistency as water. Lengthen water supply hose instead of high pressure hose. Have parts cleaned or replaced by AWSC. Make sure end of chemical hose is fully submerged into cleaning solution. No or low Worn seal or packing Have replaced by AWSC. pressure (after period Worn or obstructed valves. Have replaced by AWSC. of normal Worn unloader piston. Have replaced by AWSC. use) Water leaking at gun/ spray wand connection Loose hose connection. Worn or broken o-ring. Check and replace. Tighten. Water Loose connections. Tighten. leaking at Piston packings worn. Have replaced by AWSC. pump Worn or broken o-rings. Pump head or tubes damaged from freezing. Have replaced by AWSC. Have replaced by AWSC. Pump Pulsates Nozzle obstructed. See Nozzle Cleaning paragraph in the Maintenance section for the correct procedure. Oil leaking at Oil seals worn. Have replaced by AWSC pump Loose drain plug. Worn drain plug o-ring Worn fill plug o-ring. Pump overfilled. Incorrect oil used. Vent plug is clogged. Tighten. Check and replace. Check and replace. Check for correct amount. Drain and fill with correct amount and type of oil. Clean vent plug; blow air through it to remove any blockage. If prob lem per sists, replace plug. AWSC = Authorized Warranty Service Center A16091 18- ENG ACCESSORIES ACCESSORIES Recommended accessories for use with your pressure washer are available for purchase from your local retailer or authorized service center. If you need assistance in locating any accessory for your tool, please call 1-800-888-2468 or visit our website The use of any other accessory not recommended for use with this tool could be hazardous. Use only EXCELL branded accessories rated equal to or greater than the rating of the pressure washer. REPAIRS To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by an Authorized Warranty Service Center. Always use identical replacement parts. For the location of the nearest Authorized Warranty Service Center call 1-800-888-2468 or visit our website 19 - ENG A16091 LIMITED WARRANTY LIMITED WARRANTY ONE YEAR LIMITED WARRANTY ON PRODUCT COMPONENTS Black & Decker (U.S.) Inc. warrants to the original purchaser that the frame, wheels, gun, hose, wand, spray nozzle(s) and other components of the DeVap pressure washers covered under this warranty are free from defects in material and workmanship for one year from the date of purchase. Black & Decker will repair or replace, at Black & Decker option, products or components which have failed within the above warranty periods. Service will be scheduled according to the normal work flow and business hours at the service center location, and the availability of replacement parts. All decisions of Black & Decker with regard to this limited warranty shall be fi nal. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RESPONSIBILITY OF ORIGINAL PURCHASER (Initial User): • To process a warranty claim on your DeVap pressure washer, return it to the place of purchase or an authorized service center. • Retain original cash register sales receipt as proof of purchase for warranty work. • Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s). THIS WARRANTY DOES NOT COVER: • Merchandise sold as reconditioned, used as rental equipment, or floor or display models. • Merchandise that has become damaged or in...
Other models in this manual:Pressure Washers - Devap A16091 (1.61 mb)