Votes - 4, Average rating: 4.5 ( )

Manafacture: DeVillbiss Air Power Company File size: 5.94 mb File name: Language of manual:

Use only EXCELL branded accessories rated equal to or greater than the rating of the pressure washer. REPAIRS To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by an Authorized Warranty Service Center. Always use identical replacement parts. For the location of the nearest Authorized Warranty Service Center call 1-800-888-2468 or visit our website excellpressurewasher.com. 17 - ENG A20116 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE CAUSE CORRECTION PROBLEM Add Fuel. No fuel. Engine will not start (see Pressure builds up after two pulls Squeeze gun trigger to relieve Engine Manual on the recoil starter or after initial pres sure. for further use. engine Move choke to the "Choke" Choke lever in the "No Choke" troubleshooting) po si tion. position. Spark plug wire not attached. Attach spark plug wire. Place engine switch in ON po si tion. Engine switch in OFF position. Choke lever in the "Choke" Move choke to the "No Choke" position on a "hot" engine or an po si tion. engine that has been exposed to thermal heat for a long period of time. No or low Spray wand not in high pressure. See How to Use Spray Wand pressure instructions in the Operation (initial use) Section. Low water supply. Water supply must be at least 5 GPM @ 20 PSI. Leak at high pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Water filter screen clogged. Remove and clean filter. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re- con nect water source to pump inlet and turn on wa ter source. Squeeze trigger to remove remain ing air Air in hose. Choke in the “Choke” position. Move choke to the “No Choke” po si tion. High pressure hose is too long. Use high pressure hose under 100 feet. A20116 18- ENG PROBLEM CAUSE CORRECTION Will not draw See How to Use Spray Wand Spray wand not in low pressure. chemicals paragraph in the Operation Section. Chemical filter clogged. Clean filter. Make sure end of chemical hose solution. Chemical screen not in cleaning is fully submerged into cleaning solution. Chemical too thick. Dilute chemical. Chemical should be the same consistency as water. Lengthen water supply hose instead of high pressure hose. Pressure hose is too long Chemical build up in chemical Have parts cleaned or replaced injector. by AWSC. Worn seal or packing No or low Have replaced by AWSC. pressure (after period of normal Worn or obstructed valves. Have replaced by AWSC. Have replaced by AWSC. Worn unloader piston. use) Water leaking Worn or broken o-ring. Check and replace. at gun/ spray wand Loose hose connection. Tighten. connection Tighten. Loose connections. Water leaking at Have replaced by AWSC. Piston packings worn. pump Worn or broken o-rings. Have replaced by AWSC. Pump head or tubes damaged Have replaced by AWSC. from freezing. Nozzle obstructed. Pump See Nozzle Cleaning paragraph in the Maintenance section for the correct procedure. Pulsates AWSC = Authorized Warranty Service Center 19 - ENG A20116 LIMITED WARRANTY LIMITED WARRANTY ONE YEAR LIMITED WARRANTY ON PRODUCT COMPONENTS EXCLUDING IC2 PUMP Black & Decker (U.S.) Inc. warrants to the original purchaser that the frame, wheels, gun, hose, wand, spray nozzle(s) and other components (excluding the IC2 pump) of the Excell pressure washers covered under this warranty are free from defects in material and workmanship for one year from the date of purchase. TWO YEAR LIMITED WARRANTY ON IC2 PUMP Black & Decker warrants to the original purchaser that the IC2 pump of the Excell pressure washers covered under this warranty is free from defects in material and workmanship for two years from the date of purchase. The two year limited warranty applies to the IC2 pump only. Black & Decker will repair or replace, at Black & Decker's option, products or components which have failed within the above warranty periods. Service will be scheduled according to the normal work flow and business hours at the service center location, and the availability of replacement parts. All decisions of Black & Decker with regard to this limited warranty shall be fi nal. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RESPONSIBILITY OF ORIGINAL PURCHASER (Initial User): • To process a warranty claim on your Excell pressure washer, return it to the place of purchase. • Retain original cash register sales receipt as proof of purchase for warranty work. • Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s). THIS WARRANTY DOES NOT COVER: • Merchandise sold as reconditioned, used as rental equipment, or floor or display models. • Merchandise that has become damaged or inoperat...

Download now

Please, enter two numbers from picture: